5 to 1 balun

5 to 1 balun

Pages: 1 2 [next]

• Magnetic Longwire Baluns  ^pop - Do these things do exactly what they say they do, or are they total hogwash? - Patrick lifts the lid on the MLB
  [ Hits: 29922 | Votes: 21 | Rating: 5.37 ]
• A better antenna-tuner balun - Which balun to use? The hybrid balun promises advantages over both voltage and current baluns by ZS1AN
  [ Hits: 23095 | Votes: 11 | Rating: 5.83 ]
• WB6ZQZ 3 in 1 Balun - Builing a triple ration balun, that match resonant antennas from 9 ohms to 75 ohms with 1.5:1 or less SWR
  [ Hits: 6489 | Votes: 7 | Rating: 7 ]
• Balun construction  ^pop - PDF files describing how to homebrew a 1:2.5 balun
  [ Hits: 26897 | Votes: 41 | Rating: 6.71 ]
• Building baluns  ^pop - How to easily home-brew baluns even in strange formats 1/1 - 2/1 - 4/1 - 6/1 - 9/1 - 12/1 et 16/1 for bands from 1.8 to 30 (50) MHz in french
  [ Hits: 34484 | Votes: 41 | Rating: 5.49 ]
• Baluns by Dan N5AR - There is considerable confusion about the various types of baluns, this article try to make it clear.
  [ Hits: 2272 | Votes: 0 | Rating: 0 ]
• Some Aspects of the Balun Problem - Why all the mystery surrounding baluns ? To use or not to use baluns
  [ Hits: 988 | Votes: 0 | Rating: 0 ]
• Magnetic Long Wire UnUn 9:1 - An impedance transformer (9:1) to feed a high impedance long wire (~450 ohm), down to a 50 ohm unbalanced coaxial input.
  [ Hits: 1929 | Votes: 4 | Rating: 7 ]
• When and Where to Use Baluns - Baluns are usually used by Hams to feed dipole antennas with 50 ohm coax and to transpose from ladder line feeding a multi-band antenna to the unbalanced input of an antenna tuner.
  [ Hits: 1522 | Votes: 9 | Rating: 7 ]

• Simple HF Baluns for 50/75 ohm coax - Show diagrams, winding methods and tables of some 1:1 and 4:1 baluns for 1.8 - 30 MHz suitable for use up to 200W (400W peak) on systems using 50 or 75 ohm coaxial cable input where SWR should not exceed 1.6:1.
  [ Hits: 15208 | Votes: 25 | Rating: 4.32 ]
• Air Cored 1:1 HF BALUN - An air cored 1:1 balun for 3.5 to 30.0 MHz
  [ Hits: 4183 | Votes: 7 | Rating: 3.57 ]
• 1 to 1 Current Balun - A 1:1 current balun by N5ESE
  [ Hits: 4830 | Votes: 9 | Rating: 6.13 ]
• How to Build a UN-UN - Building a 1:1 balun, aka un-un, with an Amidon Ferrite toroid core T 200
  [ Hits: 1063 | Votes: 6 | Rating: 4.17 ]

• How To Make A Homebrew 4:1 Balun  ^pop - I built a homebrew 75 meter Double Extended Zepp Antenna, And I needed a 4:1 Balun So I decided to Homebrew the Balun also. Here is how I did it!
  [ Hits: 87326 | Votes: 101 | Rating: 6.27 ]
• 1:4 Current Balun - This project is intended to aid in tuning a balanced antenna or feedline that has a high impedance 100-600 ohms
  [ Hits: 3414 | Votes: 5 | Rating: 8 ]
• 4 to 1 Balun - 4:1 FB 3061 ROD x 2 balun can handle 125 Watts
  [ Hits: 915 | Votes: 6 | Rating: 6.5 ]

• W3EDP Antenna - W3EDP antenna for 16 - 160 Meters, works by attaching the antenna to a balun and use coax to connect the antenna to the tuner.
  [ Hits: 2146 | Votes: 2 | Rating: 10 ]

• HF Multiband end fed antennas - A multiband end-fed antenna that cover 3.5 to 30 Mhz using a 1:64 Balun based on a FT240-43 core
  [ Hits: 3723 | Votes: 6 | Rating: 4.67 ]

• The W3EDP Antenna - A wire antenna feeded with an unsymmetrical feed and a 1:4 balun can be tuned from 6 to 80 meters band but can be noisier than a dipole and cause RF in the shack
  [ Hits: 797 | Votes: 2 | Rating: 10 ]

• OH7SV Matti Hohtola Ham Projects - The most modern QRP transceiver in 2004,Direct Conversion HF Transceiver with DDS LO, 50 ohm to 200 ohm HF wide band transformers, Wilkinson splitter for RX measurements, Windom baluns 2001/2004, Ferrite rod antenna for 80 meter, Magnetic Loop Antenna for 80 m, Mascot Switched PSU 9320 modification to 8A peak current, 150W MOSFET linear amplifier for 80m, 80 m HF SSB/CW Transceiver
  [ Hits: 20373 | Votes: 36 | Rating: 8.11 ]

Pages: 1 2 [next]