computer rotator control

160-meters antenna problems and solutions - Bill Orr W6SAI ham radio techniques. Improving ground connection, computer analysis of the antenna, modelling sample antennas pdf file

Receiving antenna for low bands  ^pop - K9AY loop antenna installed at PA6Z Contest group. This is a receiving antennas for the low bands (160m, 80m and 40m). Include schematics and info on a building the control box, preamplifier and low-pass filter

LoopControl - HB9MTN loop motor control software. For motor control, either Centronics, RS232 or USB ports can be used, for CAT-Control the RS232 or USB ports.

A remote antenna tuner - Interesting project to remotely control, using a servo control circuit, a common commercial antenna tuner by N30X

JR6NJD remotely-controllable receiver - JR6NJD offer a web-controlled Icom PCR-1000 receiver radio, located in Beppu, Oita, Japan

HA1YA Mechanics & Electronics Inc. - Specializes in manufacture of middle and high power RF decks and high quality linear amplifiers with metall ceramic tubes for HF, 6m, 2m and 70 cm bands. Transverters, power supplies and control units

The KISS Protocol - The KISS TNC provides direct computer to TNC communication using a simple protocol. KISS is a simple Host-to-TNC communications protocol

IC7000BKT Icom IC-7000 CAT Control - CAT Control for Icom IC-7000 for windows. Management and synchronization of all memory bank, Management filters, volume, tones, DUP, DTCS, import export, audio recording and log frequency and signal,Auto CQ audio for repetitive calls

WEController - This software let you to control a pair of stepper motors, for three principle jobs: coil tuner, manual tuner control and satellite rotor control

glfer - glfer is a program for reception and transmission of QRSS/DFCW signals. It is composed of two main parts: the spectrogram window, where you can see the spectrum of the received signal vs. time the transmission functions, to emit cw characters at a slow but precisely controlled speed, using the QRSS (slow CW) or DFCW (Dual Frequency CW) modes

RadioDXCluster - MacOSX configurable terminal software used to control your TNC (Terminal Node Controller) to connect with your local AR-DX Cluster using your radio. This program combines features contained in MacTNC, a TNC control program, and NetDXCluster (formerly MacDXCluster), similar software that accesses DX Clusters via the Internet rather than a radio link.

Century Club Logger - Century Club Logger is for any individual whether they are a Net Control Station or just a user checking into any of the 3905 Century Club Nets who needs to maintain accurate records about all aspects of particular net.

Fast Morse - Macintosh morse code software, Fast Morse will convert any text you enter into the original Morse code equivalent, and play it on your speakers. The speed can be adjusted to anything from 1 to 35 words per minute if your computer can keep up, allowing you to send Morse signals at a rate your friends and fellow Morse enthusiasts can follow!

Black Cat CW Keyer - Black Cat CW Keyer for Macintosh lets you send morse code from your computer. You can type out the text to be sent (immediately or buffered) as well as create and send from one key

MacTNC - MacTNC is simple, configurable terminal software used by amateur (ham) radio operators to control a TNC (terminal node controller). MacTNC performs most of the same functions of other terminal software, but includes buttons for standard commands, and allows the user to configure additional buttons for special purposes. MacTNC works only user Mac OS X because it relies on Unix components of the current operating system.

Radio Control Program ARCP-480 - This free software is an application solely for the use of controlling the Kenwood TS-480. Can be used to edit, save, and export to the TS-480 information such as Memory, Menu, and Auto Mode frequencies.

FRG-Controller by Frans Vink - Free prgram to control Yaesu FRG 100 SW receiver with a PC

Radio Shack PRO-2052 remote control - Remote control software for the Radio Shack PRO-2052 dual trunking scanner

SCAN505 - A simple freeware scanner program for the Kachina DSP505. The software does NOT control the radio thru the interface port - it works in conjuction with the Kachina control software using the file interface

Virtual Legacy Radio - Windows remote control for Yaesu or Icom. Displays the current transceiver settings frequency, mode, and others on the PC in an old-fashioned way that corresponds to the look of receivers in 70's. DX-Cluster Watch (DCW) is an application that automatically refreshes a web page with the dx-cluster content, parses spot lines from it, keeps a consolidated list and inserts the spots to VLR as frequency markers by OK1FIG

TS-2000/B2000 Memory Control Program - This program is for downloading, uploading the memory channels and various settings on the TS-2000(X)/B2000. To write data to or read the data from the TS-2000(X)/B2000 memory, an RS-232C straight cable is required. Runs on Windows 98.

Memory Control Program MCP-1A - Kenwood TM-271A / TM-271E / TM-471A. By utilizing this software, you can enjoy the versatility of the TM-271 Series transceiver through the memory channel management and edit functions.

TH-F6A / TH-F7A / TH-F7E Memory Control Program - By utilizing this software, you can enjoy the versatility of the TH-F6/ F7 transceivers through the memory channel management and edit functions.

SoundCard Packet TNC PC to Radio Interface - Computer sound card packet tnc to radio interface. david stansbury kb3kai home-brew version of this soundcard to rig adapter

Vacuum Tube Software - The VTDATA software package is a complete vacuum tube manual on your computer. It has all the information you'd expect in a tube manual. VTDATA's database also includes vacuum tubes of historical interest, such as the early "two digit" types (45, 80, etc.) and hi-fi audio types.