j match

The DXZone.com

Search Results for "j match"

77 links

Antennas : 160M
  • T antenna with matching network for 160 m - 160m T Antenna broadcast design by Guglielmo Marconi has been built and is used by Jim NN4AA on 160m. Article by G7LRR
    [ Hits: 2781 | Votes: 6 | Rating: 4.67 ]
Antennas : 2M
  • 12el 144MHz Plus2 LFA  updated Priority listing - A Low-Noise Urban 12 element Plus2 LFA Yagi antenna for 144MHz no match required, 50Ohm direct feed
    [ Hits: 2279 | Votes: 7 | Rating: 7.14 ]
Antennas : 6M
  • A Hairpin match for 5 el. Tonna - How to improve the gain of your 5 element Tonna yagi for 50 MHz by roughly 3 db! by PA2HJS
    [ Hits: 1499 | Votes: 3 | Rating: 5.67 ]
  • 11el 50MHz Low Noise LFA Yagi - A Large 11 element LFA Yagi for self build. Easy construction as no matching is required. Super gain, F/B and flat SWR
    [ Hits: 634 | Votes: 5 | Rating: 7.80 ]
  • 10el 50MHz Low Noise LFA Yagi - A high gain LFA 10 element LFA Yagi with super clean pattern and flat SWR no matching required so easy to build.
    [ Hits: 852 | Votes: 2 | Rating: 5.50 ]
  • 9el 50MHz Low Noise LFA Yagi - A 9 element 6M LFA Yagi with no matching required. Super flat SWR, great pattern and gain too. What more do you need?
    [ Hits: 327 | Votes: 0 | Rating: 0.00 ]
  • 7el 50MHz 9.7mtr LFA Yagi Priority listing - A 7element 9.7 metre long 6M LFA Yagi. flat SWR with no match required. Supper pattern, Gain and F/B
    [ Hits: 336 | Votes: 0 | Rating: 0.00 ]
Antennas : End-Fed Antennas : Feed Lines
  • L Match ATU for QRP - The L match is designed for the matching of random and long wires and should not be mounted in a metallic box/case, i used a small plastic food container which was the most expensive part of the project.
    [ Hits: 4630 | Votes: 7 | Rating: 7.00 ]
  • The Clemens Match by W9ERN - Balanced feed with coaxial line by John F. Clemens W9ERN
    [ Hits: 523 | Votes: 2 | Rating: 4.50 ]
Antennas : Homebrewing Techniques
  • From Transmitter to Antenna - A collection of articles on the subject of impedance, impedance matching and high-frequency power transmission by G3YNH
    [ Hits: 1007 | Votes: 0 | Rating: 0.00 ]
Antennas : J-Pole
  • Super J-Pole for 435MHz - The Super J Pole antenna is a co-linear vertical consisting of a number of half wave length vertical elements separated with half-wave length stubs (Tuning stub) feed with a folded matching stub by vk6ysf
    [ Hits: 3169 | Votes: 6 | Rating: 5.00 ]
Antennas : Theory
  • Single-stub matching - Single-stub matching of transmission lines to loads A worked example
    [ Hits: 423 | Votes: 6 | Rating: 4.00 ]
Antennas : Theory : Impedance matching
  • Simple VHF Gamma Match - Plan of a simple VHF & UHF Gamma match contrstruction
    [ Hits: 6640 | Votes: 32 | Rating: 6.15 ]
Antennas : Tuners
  • 10 m Aerial Matching Unit - This simple matching unit will allow a 10 meters aerial to be used right across the 10m band without the need to physically adjust the elements, and offers a virtual 1:1 VSWR at 50 ohms impedance to the transmitter.
    [ Hits: 3256 | Votes: 2 | Rating: 4.50 ]
  • Switched inductor L match tuner - A 10 to 80 meters band qrp antenna tuner by KC8AON, based on Steve Weber, KD1JV "ALT or Altoids L Tuner"
    [ Hits: 5721 | Votes: 7 | Rating: 7.28 ]
  • A Portable Antenna Matching Unit - A small HF antenna tuner project for qrp operations. Includes circuit diagrams pictures and test results by GW4ALG
    [ Hits: 13861 | Votes: 5 | Rating: 5.40 ]
Manufacturers : Antennas : HF : Mobile Antennas
  • The ElectraSlide Antenna - Modification of the DK3 design by Don Johnson, W6AAQ. No voltage dropping, operates on the full 12 volts. The control switch and the matching toroid are supplied. All you need is a standard 3/8 by 24 thread ballmount, 2 wire sheilded microphone cable for control wiring, and a CB whip cut to resonance.
    [ Hits: 1249 | Votes: 0 | Rating: 0.00 ]
Operating Modes : Weak Signal
  • Using MT65 - MAP65, a panoramic, polarization-matching receiver for JT65 by K1JT
    [ Hits: 284 | Votes: 0 | Rating: 0.00 ]
Software : Weak Signal
  • MAP65 - MAP65 works together with the Linrad software. The Linrad/MAP65 combination implements a wideband, polarization-matching receiver for the JT65B protocol.
    [ Hits: 308 | Votes: 1 | Rating: 9.00 ]
Not satisfied ? Lookup Google Custom Search Engine for j match


Search j match with: Yahoo!, Teoma, Lycos , Bing

j match

Related Searches

Get our links, Everywhere!

Follow us on Social Networks
RSS Feeds The DXZone.com RSS feed

Sign up for daily Newsletter

Service provided by Google FeedBurner

Free for your Site

Add our gadgets to your site
Daily Top 10 links

Google Custom Search