multi mode

multi mode

Pages: [prev] 1 2 3 4

• How to Blow Up Your Balun - In this article, author examine stresses placed on common-mode chokes (aka baluns) as hams use/abuse them, examine the efficiency of simple dipole multi- band antennas and their feed systems. Stressing a Balun.
  [ Hits: 387 | Votes: 0 | Rating: 0 ]

• Multi-Band End-Fed Antenna Design for Limited Space  ^new - This document details the construction of a multi-band end-fed antenna, suitable for situations with limited space for larger antennas. The design utilizes a 1:49 to 1:60 impedance transformer to match a half-wave wire antenna fed at one end. Compared to a traditional dipole, this antenna resembles a highly unbalanced Windom antenna with one very long leg and a virtual short leg. The design eliminates the need for radials but relies on the coax cable shield for grounding. The document recommends using at least 10 meters of coax and installing a common mode filter at the entry point to the shack for improved performance.
  [ Hits: 76 | Votes: 0 | Rating: 0 ]

• Modeling an 80/40/20M Fan Dipole for DX - An interesting presentation of a real multiband Fan Dipole antenna, optimized for better DX operation performances, considering the terrain, position, DX destination path and other influencing factors
  [ Hits: 538 | Votes: 2 | Rating: 5.5 ]

• Moxon Mania - Building the Ultimate 4-Band Moxon Antenna - The article details the design and construction of a four-band Moxon beam by a radio amateur. The beam, mounted atop a rooftop tower, aimed for gain over a dipole on 20 meters, cost under $500, and included additional bands. The design features fiberglass spreaders, four bands (20/15/10/6 meters), and a single feedpoint. The construction involved computer modeling, NEC source code, and specific dimensions. The article outlines the assembly, materials, and tuning process, including in-situ adjustments for optimal performance. Despite initial challenges, the beam improved signal strength and facilitated contacts on multiple bands, marking it as the best HF antenna the author has owned.
  [ Hits: 96 | Votes: 0 | Rating: 0 ]

• Chokes and Isolation Transformers for Receiving Antennas - Chokes and isolation transformers are essential for receiving antennas to mitigate common mode current, which induces noise and interferes with signal quality. Common mode chokes, formed by winding feedline through ferrite cores, block unwanted current effectively. Proper selection of core material and winding turns ensures resonance near the operating frequency, reducing interference. Isolation transformers further minimize interference, crucial for multi-transmitter stations.
  [ Hits: 59 | Votes: 1 | Rating: 9 ]

• Treehouse YSF reflector - The treehouse project is an YSF reflector with multiple rooms. You can change rooms via the dashboard or DGID on your radio. See radio model on the dashboard, Supports VW and DN mode,Change rooms on dashboard
  [ Hits: 101 | Votes: 1 | Rating: 10 ]

• CTR2-Mini Radio Controller - CTR2-Mini is a small radio controller based on the Seeed Studios Wio Terminal. It can control many radios including FlexRadio 6000s. Multiple Minis can be used to control multiple slices on the Flex. It also has a special mode that allows two CTR2-Minis to control the Main and Sub VFOs on the FTdx101. An article on CTR2-Mini appears in the September 2022 issue of QST.
  [ Hits: 93 | Votes: 0 | Rating: 0 ]

• IC-7300 Quick Start Guide - PDF document for IC-7300 beginners. The ICOM IC-7300 is an HF + 6 meter, multi-mode, self-contained Software Defined Radio (SDR) transceiver with knobs, buttons and a touch screen. It also has a real-time spectrum display with pan adapter and water fall displays.
  [ Hits: 697 | Votes: 2 | Rating: 8 ]

• Arduino QRP Transceiver: DIY Success on HF Bands - This article introduces an Arduino-based QRP CW Transceiver designed for lower HF bands. The journey begins with the Wotduino, evolving from a keyer to a multi-mode beacon. The development includes a QRP transmitter and culminates in a receiver inspired by Roy Lewallen design. The transceiver, controlled through a control bus features a signal path, modulation, filtering, and adjustable frequency settings. Despite initial testing intentions, successful QSOs on 80 and 40 meters showcase its functional capabilities.
  [ Hits: 109 | Votes: 1 | Rating: 1 ]

• 70 cm Repeater Project - Multi Mode 70cm DIY Repeater Build Project made with two Tait TM8235 and acting as modem a Repeater Builders MMDVM plus a Raspberry PI
  [ Hits: 48 | Votes: 0 | Rating: 0 ]

Pages: [prev] 1 2 3 4