pc 385 schematic

J Pole antenna for 6 meters - Homebrewed jpole antenna for 50 mhz by IW0BZD, include pictures and schematics, in italian.

160 m receiving loop - KC22TX receiving loop antenna for 160 meter band

LoopControl - HB9MTN loop motor control software. For motor control, either Centronics, RS232 or USB ports can be used, for CAT-Control the RS232 or USB ports.

Idiot's guide to antennas - A very basic guide to antennas concept. Explain the usage of dummy load, basic antennas like dipole o j-poles.

Transoceanic resource library - Transoceanic radios, zenith radios, service data, pictures schematics, manuals and owners data.

Antique Radio Schematics and Capacitors for Tube Radios - Specializes in antique radio schematics and capacitors. carries antique radio schematic diagrams and electronic circuit service information for american, canadian and european antique radios.

Antique automobile schematics - Antique automobile radio repair and schematics

Atwater Kent Home Page - This is a "techie" site, dedicated to presenting service manuals, parts lists, schematic diagrams and other information of value to restorers and technicians who try to keep these radios working

Canadian Antique Radios Schematics Diagrams Service - We specialize in canadian antique radio schematics for vintage tube radios made in canada. we carry lots of factory electronic circuit schematic diagrams as well as all rcc / radio college of canada service data 1920's - 70's.

Philco ServiceMan - Schematics and general info like service manuals for philco radios

EPC PSK63 QSO Party - The european phase shift keying club (epc) sponsor of the PSK63 QSO party

W4MLB Platinum Coast Amateur Radio Society - Platinum coast amateur radio society (pcars) w4mlb - melbourne florida, pcars provides hf, vhf, and uhf communications for any police fire and rescue emergency

W4FPC Flagler Palm Coast Amateur Radio Club - Club is located in Flagler County, Florida mid-way between St. Augustine and Daytona Beach.

European PSK Club - The European PSK Club, or EPC for short, is an informal club of amateur radio operators dedicated to maintaining high levels of amateur radio communications on PSK modes. Its purpose is to promote activity and good operating practice on the PSK modes on all amateur bands

JR6NJD remotely-controllable receiver - JR6NJD offer a web-controlled Icom PCR-1000 receiver radio, located in Beppu, Oita, Japan

I0SKK - 10 MHz QRPp beacon - Pictures and schematics about QRPp experiments using QRSS on Ham Bands as 10 MHz, 7 MHz,

HeathKit SB200 Mods - SB-200 Notes, SB-200 mods schematic. SB-200 mods photos

AGWTracker Pocket - APRS client for pocket pc platform

DSCdecoder - DSCdecoder decodes the DSC digital signals from ships and coast stations using the sound card in your PC. You need a suitable MF, HF or VHF band radio receiver tuned to one of the DSC distress and calling channels or to one of the Navtex channels

Cleverscope - The PC USB mixed signal oscilloscope - Cleverscope PC based oscilloscopes, spectrum analyzers and signal generators

Packet Engine Pocket PC - Packet Engine For PocketPC (Windows Mobile 5 and more). It can be used with KISS TNCs only.

Virtual Legacy Radio - Windows remote control for Yaesu or Icom. Displays the current transceiver settings frequency, mode, and others on the PC in an old-fashioned way that corresponds to the look of receivers in 70's. DX-Cluster Watch (DCW) is an application that automatically refreshes a web page with the dx-cluster content, parses spot lines from it, keeps a consolidated list and inserts the spots to VLR as frequency markers by OK1FIG

Homebrew HF Amp with 3CX3000F7 - Grounded grid triode HF linear amplifier with pictures and schematics diagrams by W2DTC. The amp design was for 160 80 40 and 20 meters

Idiot's guide to coaxial cable  ^pop - A very beginner's guide to coax cables. Characteristics, detailed comparison of typical coaxial cables, commonly used connectors, and a few words about SWR.

A good regenerative receiver - A good SSB-CW-AM regenerative receiver with a fine tuning by moving the wooden stick with a grounded piece of PCB towards the coil.