terminal

34 links

History of the Hexbeam Antennas - The original HEXBEAM was developed by Mike Traffic, N1HXA, in the early nineties. It is true that an M over W configured yagi antenna that resembled a butterfly was earlier tried successfully. But the advanced electrical design, the characteristic nesting concept and central terminal post that enable the multi band functionality along with the basic hardware design were all developed by Mike Traffie.
[ Hits: 130 | Votes: 2 | Rating: 7.5 ]

Bootstrap coax traps for antennas - Analysis of an antenna trap where a coil is formed of a length of coax cable, the outer conductor of one coax end is tied to the inner conductor of the other coax end, and the remaining connections form the terminals for the trap.
[ Hits: 1356 | Votes: 2 | Rating: 9 ]

Putting a Balun and a Tuner Together - Two wire transmission line as a three terminal Device , The W2DU and W7EL models of a choke balun, The effectiveness of a balun. Article by Kevin Schmidt, W9CF
[ Hits: 3974 | Votes: 5 | Rating: 6.2 ]

Timewave - Sells leading-edge voice and digital communications products to the world-wide military, government, industrial, and amateur radio marketplaces. Bluetooth Remote Audio/PTT, Rig Controller with Audio & PTT , HamLinkUSB Rig Control, Noise filtersm antenna analyzers, Multimode Data Controller, TNC, Packet Radio Terminal Node Controller. USB2RS232
[ Hits: 4103 | Votes: 3 | Rating: 5.33 ]

SWR ANTENNA ANALYZER + WSPR TX - Available worldwide can be used as Arduino Shield or plug it in to you PC , or with a bluetooth adapter connect to Android. With a highly optimized software, KAI200 brings you: a. Antenna analyzer form 1 up to 200 Mhz; b. WSPR transmiter (set up by serial terminal); c. Square Wave Signal generator KAI200 is all you need for your radio whatever it is Yaesu, Icom, Kenwood or Drake and DIY projects.
[ Hits: 326 | Votes: 8 | Rating: 9.62 ]

CTR2-Mini Radio Controller - CTR2-Mini is a small radio controller based on the Seeed Studios Wio Terminal. It can control many radios including FlexRadio 6000s. Multiple Minis can be used to control multiple slices on the Flex. It also has a special mode that allows two CTR2-Minis to control the Main and Sub VFOs on the FTdx101. An article on CTR2-Mini appears in the September 2022 issue of QST.
[ Hits: 93 | Votes: 0 | Rating: 0 ]

M8000 Terminal Software - This software allows your PC to connect to the Universal Radio M-8000 Decoder through its serial port in order to get and save the decoded data but also to send commands to the decoder.
[ Hits: 1442 | Votes: 7 | Rating: 7.57 ]

LinPac packet radio terminal - Linpac is an extensible Linux packet terminal that supports easy access to concurrent connections (streams), PBBS/FBB forwarding, and support for adding external commands
[ Hits: 1873 | Votes: 2 | Rating: 10 ]

MacTNC - MacTNC is simple, configurable terminal software used by amateur (ham) radio operators to control a TNC (terminal node controller). MacTNC performs most of the same functions of other terminal software, but includes buttons for standard commands, and allows the user to configure additional buttons for special purposes. MacTNC works only user Mac OS X because it relies on Unix components of the current operating system.
[ Hits: 7139 | Votes: 11 | Rating: 6.94 ]

CwType ^updated - The terminal program for CW-operators. You can transmit both from the keyboard and from a paddle connected to game or LPT ports. You can also operate in paddle iambic mode. Control of the transceiver (PTT and CW keying) is made through one of the COM or LPT ports. CwType can integrate with AALog software
[ Hits: 2806 | Votes: 2 | Rating: 5 ]

PacTerm for Windows - PacTerm for Windows is a commercial host mode terminal software for the Kantronics TNCs takes advantage of the true multitasking capabilities of Windows.
[ Hits: 3496 | Votes: 8 | Rating: 7.5 ]
TNC - The Packet Terminal Driver program is a general purpose communications package for communicating with a packet TNC attached to your IBM-PC/clone. The program was written to work with the Kantronics range of TNC's but should work with any TNC that is connected to a serial port on your computer.
[ Hits: 3955 | Votes: 1 | Rating: 1 ]

Win4IcomSuite ICOM Radio Control Software - The Ultimate Control Software for the IC-7300, IC-7610, IC-7600, IC-7850, IC-7851 and Others is a control software suite that includes additional interesting features such as support for the built in Spectrum Scope, Audio monitors, Shortwave DB, CW Terminal, Clublog Spotting, Memory management, interface to Ham Radio Deluxe Logbook, DM780, n1mm+, log4om, DXLab and other. Runs on Windows OS, commercial licence.
[ Hits: 364 | Votes: 1 | Rating: 1 ]

Arduino CW Terminal - This article describes firmware and minimal hardware for encoding and decoding of on-air CW using an terminal/modem based on these controller boards.
[ Hits: 677 | Votes: 0 | Rating: 0 ]