usb cable

144MHz Slim Jim antenna - 2 Meter band Slim Jim antenna using a 300 Ohm ribbon cable

2 Metre Slim Jim Antenna Project. - Homebrew a vhf slim jim antenna with a 300 ohm ribbon cable

QRP Magnetic longwire balun with VHF-splitter - This Magnetic Longwire Balun (MLB) makes it possible to efficiently use a coaxial lead-in cable with all forms of longwires, T-forms or other types of wire antennas, without the need for an antenna tuner.

Bootstrap coax traps for antennas - Analysis of an antenna trap where a coil is formed of a length of coax cable, the outer conductor of one coax end is tied to the inner conductor of the other coax end, and the remaining connections form the terminals for the trap.

Wire Antennas for the Beginner - 1983 - ARRL QST Wire Antennas for the Beginner June 1983

Voldatech - Voldatech Telecommunication & Networking Solutions, RF Coax cables and connectors manufacturer based in China

HuberSuhner - Prime source for precision cables and connectors based in switzerland

Teledao - Manufacturer of Grounding kits, cable, copper lugs, bus bars, brackets, lightning arrestors for coaxial feeder cable & fiber cable lightning protection & grounding

Aaronia AG - Spectrum Analyzers - Handheld RF Spectrum Analyzer, EMC & Pre-Compliance Antennas, USB Analysers, Near Field Probes, EMF Shieldings

K2 modifications - General modifications applicable to any Elecraft K2

Voice keyer with TS-590 - Setting up Digital voice keyer via USB for Kenwood TS-590

N1MM and TS-590S - Step by step instructions for setting up N1MM Logger to communicate with the TS-590S using the USB connection

CAT cable schematic for FT 817 857 897 - To connect up your FT-817/857/897 to a PC you have a number of options. For the serial connection you can go ahead and obtain a CT-62 from YAESU. Alternatively you can make up your box with a level converter and cable using schematic in this page

Programming the Baofeng UV-3R - How to program memories on UV-3R using the prolific usb cable

SWL Antenna Distribution System - a methodology for connecting multiple LF/MF/HF receivers to a single antenna via readily available and inexpensive 75-ohm TV cable.

K9DUR Voice Keyer - Voice Keyer was specifically written to interface to PowerSDR via Virtual Audio Cable (VAC)

Fitting an N connector plug - Fitting N connectors to coax cable

IC-92 Programming Cable schematic - Homebrew ICOM IC-92 programming cable following this 12-pin connection schematic by KA0BBQ

Homemade OPC-474 cable - Homemade programming cable works with IC-E90, IC-E208,IC-E2820, IC-2100, IC-2200, IC-2720 IC-2725 IC-2820 and more by MW0GKX

IC-E80 Home made programming cable - Make an OPC-478 PC Cloning / CI-V cable, work with IC-2725, IC-2800, IC-2820 , IC-E80 By MW0GKX.

Yaesu cloning cables - Make a Yaesu cloning cable for Yaesu radios ft-847, ft-857, ft-23, ft-90 FT-1500, FT-1802, FT-2800, FT-2400, FT-2500

ICOM CI-V interface to RS232 cable - ICOM CI-V interface to RS232 using transistors, fits in DB9 case

Make a Yaesu CT-27A cloning cable - Make a Yaesu CT-27A cloning cable By Brian, MW0GKX.

Icom OPC-1529R programming cable - Home build an OPC-1529R cable, works with IC-91, IC-2200, IC-V82, IC-U82, ID-E880 by MW0GKX.

NEQRP Noise Bridge - A noise bridge is a device for measuring or comparing impedances on coaxial cables, antennas, components, etc.