10 meter band antenna

177 links - and 1 categories

Magnetic Monster Loop Antenna for 160m - A monster magnetic loop antenna for 160 meters band. This Magnetic loop is optimized for 1840 Khz + 50 Khz. PDF Article published on La Radiospecola 10.22
[ Hits: 849 | Votes: 2 | Rating: 10 ]

Speaker Wire Delta Loop Antenna for 20M - The antenna I built was inspired by a portable delta loop designed by Doug DeMaw, W1FB. Given that I constrained myself to a 50-foot roll of speak wire, I scaled my antenna for the 20M band. Using the formula, 1005 divided by the frequency in megahertz, I calculated a total length of 71 feet (21.6 meters) for the center of the 20M band.
[ Hits: 127 | Votes: 0 | Rating: 0 ]

Coax Dipole for 2 meters band - A homebrew 2m 144.2 MHz vertical 1/2 wave Coaxial Dipole antenna project for your home QTH, SOTA, portable field operations/WICEN exercises or the emergency 2m Go-box. Elsewhere in amateur radio circles this antenna is known as a 2m Flower Pot Antenna
[ Hits: 250 | Votes: 3 | Rating: 6 ]

Low Bands Battle Creek Antenna - This antenna is designed for 40, 80 and 160 meters to complement a tri-band beam normally taken on DX peditions for 10, 15 and 20 meters, so six bands can be worked with only two antennas.
[ Hits: 137 | Votes: 0 | Rating: 0 ]

A Cobwebb antenna homebrew - A homebrew cobwebb antenna for HF bands covering from 10 to 20 meters band.
[ Hits: 179 | Votes: 1 | Rating: 10 ]

The Pop-Up Vertical 2.0 - Basically, this antenna is a 23-foot wire fed through a 4:1 un-un transformer. This antenna can be easily used in portable operation, for operating all bands from 40-10 meters.
[ Hits: 254 | Votes: 0 | Rating: 0 ]
8010 Enfed Antenna - With this antenna the coverage is 80,40,20,15 and 10 meter band without any antenna tuner and the average SWR is below 1.2 on phone bands. The total antenna lenght is about 23 meters , with one 20.4 meters long segment from the 1:49 transformer to the 110uh coil and about 2.2 meters long segment from the coil to the insulator.
[ Hits: 142 | Votes: 0 | Rating: 0 ]
Multi-Band End-Fed Antenna Design for Limited Space ^new - This document details the construction of a multi-band end-fed antenna, suitable for situations with limited space for larger antennas. The design utilizes a 1:49 to 1:60 impedance transformer to match a half-wave wire antenna fed at one end. Compared to a traditional dipole, this antenna resembles a highly unbalanced Windom antenna with one very long leg and a virtual short leg. The design eliminates the need for radials but relies on the coax cable shield for grounding. The document recommends using at least 10 meters of coax and installing a common mode filter at the entry point to the shack for improved performance.
[ Hits: 76 | Votes: 0 | Rating: 0 ]

Square Halo Antenna for 10 and 20 Meters - How to build a limited space 10 and 20 meter band Square Halo DX antenna. A horizontally polarized antenna for 10 and 20 meter band, which is suitable for a limited space.
[ Hits: 241 | Votes: 1 | Rating: 9 ]

Home made multiband MOXON - Multi band Moxon Yagi Antenna for 10,15,20 meters band with just one feed line. Drawing and project with dimensions
[ Hits: 488 | Votes: 0 | Rating: 0 ]
Moxon Mania - Building the Ultimate 4-Band Moxon Antenna - The article details the design and construction of a four-band Moxon beam by a radio amateur. The beam, mounted atop a rooftop tower, aimed for gain over a dipole on 20 meters, cost under $500, and included additional bands. The design features fiberglass spreaders, four bands (20/15/10/6 meters), and a single feedpoint. The construction involved computer modeling, NEC source code, and specific dimensions. The article outlines the assembly, materials, and tuning process, including in-situ adjustments for optimal performance. Despite initial challenges, the beam improved signal strength and facilitated contacts on multiple bands, marking it as the best HF antenna the author has owned.
[ Hits: 96 | Votes: 0 | Rating: 0 ]

Homebrew an OCF Off-Center Fed Dipole Antenna - This type of antenna is a popular antenna design as the performance is very good across the HF bands and requires little or no tuning. It’s a dipole fed off center with a 4:1 balun at the offset feed point. The antenna shown covers 80, 40, 20 and 10 meters. The formula can also be used to adjust the overall length to cover more or fewer bands and the resulting overall length. 160-10m, 80-10m or 40-10 meters depending on your available space. Other bands will require a tuner.
[ Hits: 198 | Votes: 3 | Rating: 6.67 ]

Build this Vertical Portable HF Antenna - An experimental prototype of an asymmetrical hatted vertical dipole antenna that can work on HF bands 20 to 10 meters band. The AHVD Vertical dipole is an upside-down T design
[ Hits: 374 | Votes: 3 | Rating: 9.67 ]

A simple Attic Antenna for HF bands - This simple antenna was installed on the attic. Antenna was matched with help an Automatic ATU in 40, 30, 20, 17, 15, 12 and 10 meter amateur Bands. The Antenna worked satisfactory on the above mentioned bands.
[ Hits: 317 | Votes: 7 | Rating: 6 ]

20-30m Vertical Antenna - Homebrew project for a vertical antenna with a coaxial-cable trap, that works on 20 and 30 meters band.
[ Hits: 73 | Votes: 0 | Rating: 0 ]

The Squid Pole Wire Antenna Re-visited - The author explores enhancing the performance of a 7-meter fiberglass squid pole wire antenna for amateur radio. The wire, resonant at 10MHz, poses impedance challenges on various bands. Experimenting with direct coax feed and UN-UN transformers, the LDG Z11-Pro2 auto-tuner is found effective but may show deceptive SWR readings. The author employs adjustable UN-UN ratios and introduces a custom "porcupine" coil to optimize the antenna's efficiency.
[ Hits: 91 | Votes: 0 | Rating: 0 ]

NA4RR HexBeam - NA4RR manufacture a six band hexagonal beam antenna for ham radio, covering 6, 10, 12, 15, 17, and 20 meter.
[ Hits: 157 | Votes: 0 | Rating: 0 ]