arduino ham

The DXZone.com

arduino ham

24 links - and 1 categories

Antennas : Magnetic Loop
  • Magnetic Loop Controller for 4 Antennas - This project is for those ham amateurs who do not have a commercial one . It's easy to build with a soldering iron, a plastic case and a little knowledge of arduino. The controller is made with budget components you can find easily in Internet. The main component is a cnc shield that fits over an Arduino Uno. Both made a compact, small and cheap controller.
    [ Hits: 133 | Votes: 2 | Rating: 10 ]
Operating Modes : QRSS
  • Ganymede - QRSS TX - Designs for QRSS TX and other Arduino based systems
    [ Hits: 379 | Votes: 0 | Rating: 0 ]
Technical Reference : Arduino
  • HamShield for Arduino - HamShield is a powerful VHF UHF transceiver that lets your Arduino talk to far away people using ham radio bands
    [ Hits: 1088 | Votes: 2 | Rating: 4 ]
  • Rotator Control for HyGain HAM-IV - Hy-gain HAM-IV rotator control with Arduino by OK1BIL
    [ Hits: 1676 | Votes: 1 | Rating: 1 ]
  • SWR / Wattmeter with Arduino Uno Shield - SWR / Wattmeter with Arduino Uno Shield. It can measure from 2 to 200 watt and SWR for HF Ham radio.
    [ Hits: 8914 | Votes: 38 | Rating: 5.77 ]
  • Ham Radio Arduino Projects - Ham Radio applications with the Arduino micro-controller presentation
    [ Hits: 5034 | Votes: 12 | Rating: 6.25 ]
  • Frequency Counter with Arduino - An interesting project about an Arduino-based frequency counter fot the Kenwood TS-520S
    [ Hits: 1803 | Votes: 8 | Rating: 5.58 ]
  • ARDUINO Simplex Repeater Controller - This project hereby presented is a complete HAM radio simplex 'smart' repeater, built around a Motorola GM-350/950, Arduino NANO board and a WINBOND audio recording integrated circuit
    [ Hits: 1074 | Votes: 6 | Rating: 3.67 ]
  • Arduino Iambic Keyer and Side Tone Generator - A project to implement a simple and efficient CW Keyer and a side tone generator with Arduino
    [ Hits: 612 | Votes: 0 | Rating: 0 ]
  • Airgate - A Receive-Only, Low-Power APRS iGate made with Arduino
    [ Hits: 149 | Votes: 2 | Rating: 4 ]
  • The WB0RIO 28 Mhz Arduino Beacon - This project involves the construction of a 5 Watt Morse code beacon transmitter that operates in the 28.200 to 28.300 section of the 10 Meter Amateur Radio band. The beacon controller uses an Arduino Uno microprocessor board to produce the three signals that control the transmitter.
    [ Hits: 626 | Votes: 0 | Rating: 0 ]
  • Automatic HF Antenna Tuner with Arduino - Make and automatic antenna tuner based on Arduino and using economic card. This ATU Project can be installed outdoors and controlled remotely by an rs485 link
    [ Hits: 570 | Votes: 3 | Rating: 9.67 ]
  • HF Arduino VNA - An home made VNA made with Arduino Nano. This project features an LCD display 4x20 works from 1 MHz to 60MHz, can use bluetooth connection with Blue VNA android app.
    [ Hits: 199 | Votes: 1 | Rating: 10 ]
  • WSPR beacon - A WSPR beacon project based on Arduino nano (atmega328P) based microcontroller
    [ Hits: 237 | Votes: 0 | Rating: 0 ]
  • Band Decoder Arduino - Arduino/ATtiny Based (Ham Radio) ICOM CIV to Yaesu BCD Band Decoder. Build a ICOM CIV to Yaesu BCD Band to automatically band switch the Yaesu Quadra Amplifier.
    [ Hits: 63 | Votes: 0 | Rating: 0 ]
Technical Reference : HF Radios
  • Stingray Marine Transceiver - Recently, at the Ballarat Hamfest, the author acquired an old Marine transceiver for just $10, charmed by its sturdy construction and waterproofing. Made by Findlay Communications in Sydney, this crystal-controlled transceiver had been dormant but was reinvigorated with minor fixes. A manual was sourced, and further repairs were made, including an ingenious crystal oscillator replacement using an Si5351a controlled by an Arduino. The refurbished radio, complete with a fresh coat of paint and added customizations, is now operational for 160m AM and 30m SSB. A successful and cost-effective restoration.
    [ Hits: 61 | Votes: 0 | Rating: 0 ]
Technical Reference : Keyers
  • NanoKeyer - An Arduino based CW contest keyer addon, ideated and designed for the use in conbination with the K3NG Arduino keyer open-source firmware.
    [ Hits: 957 | Votes: 1 | Rating: 8 ]
Technical Reference : Raspberry Pi
  • Raspberry PI remote Ham Radio Server - Remote Ham Radio via WebRTC Audio Raspberry Pi 3. Stream Transceiver Audio to and from the remote station though a Browser using WebRTC.
    [ Hits: 280 | Votes: 1 | Rating: 10 ]
Technical Reference : Repeater
  • Arduino Repeater Controller - This blog article introduces an updated repeater controller project utilizing the Arduino UNO. It includes a CW identifier, and the ID message can be customized using hex codes. The author offers a Windows command line program for easier message coding and provides a link for download. The controller features three adjustable timers for IDer, Timer-out, and Squelch-tail. The article also mentions the use of an audio switch to control audio levels between the receiver and transmitter. Detailed instructions and code files are available on the author's website for both version 1 and version 2 of the Arduino repeater controller. The project aims to enhance repeater functionality and audio management in ham radio operations.
    [ Hits: 94 | Votes: 0 | Rating: 0 ]
Technical Reference : Sound Card Radio Interfacing
  • DuinoVox USB interface - Cheap and easy to build digital modes USB interface for Ham Radio. The DuinoVOX Arduino powered digital modes USB interface for ham radio.
    [ Hits: 88 | Votes: 0 | Rating: 0 ]

Not satisfied ? Lookup Google Custom Search Engine for arduino ham


Search arduino ham with: Yahoo!, DuckDuckGo , Bing

Search

Related Searches

Get our links, Everywhere!

Follow us on Social Networks
RSS Feeds The DXZone.com RSS feed

Sign up for daily Newsletter

Service provided by Google FeedBurner

Free for your Site

Add our gadgets to your site
Daily Top 10 links

Google Custom Search