connector

The DXZone.com

connector

163 links - and 3 categories

Antennas : Receiving
  • HF Receive Antenna - This page describes a couple of parts box medicine bottle antennas that you can build. The ground side of the capacitor is soldered to the ground of the BNC connector. The positive side of the capacitor takes 5 turns around the toroid and is soldered back to itself. The center pin of the BNC connector takes 5 turns around the toroid and then continues on to the wire wound inductor. From there the antenna continues with an attached piece of wire.
    [ Hits: 189 | Votes: 2 | Rating: 3 ]
Antennas : Tuners
  • ICOM Tuner Connector - Many Icom radios e.g.7100 have a connector for automatic tuners such as the Icom AH4. The cable supplied by Icom is of a fixed length 10m and is not shielded. Icom recommends to use shielded cable for any length greater than 10m.
    [ Hits: 232 | Votes: 1 | Rating: 10 ]
Manufacturers : Cable and Connectors
  • Gigatronix Coax Cables - Manufacturers of Coaxial Connectors, Push-Pull Latching Connectors, Coaxial Cable, Multicore and Coaxial Cable Assemblies based in UK
    [ Hits: 136 | Votes: 0 | Rating: 0 ]
Radio Equipment : HF Transceivers : Icom IC-7300
  • Enhancing Icom IC-7300 RX Antenna - Despite the model limitations, such as a single TXRX antenna connector, the author shares a reversible modification involving a coax relay for enhanced functionality, demonstrating the transceiver's adaptability and customization potential.
    [ Hits: 183 | Votes: 1 | Rating: 10 ]
Shopping and Services : Ham Radio Stores
  • Midway Electronics - Midway Electronics supplies the area with electronic components, wire, cables, amateur radio transceivers, QRP kits, CB transceivers, GMRS radios, Shortwave radios, power supplies, antennas, coax, connector and ham radio accessories
    [ Hits: 215 | Votes: 2 | Rating: 3 ]
Technical Reference : 3D Printed Projects
  • 3D Printed Accessories for the FT-817 and KX2 - DC plug adaptor using an XT60 connector. 18650 Lithium battery 3 cell carrier, Three band end fed half wave antenna, XT60 chassis mounted flange.
    [ Hits: 182 | Votes: 0 | Rating: 0 ]
Technical Reference : Batteries
  • USB-C charging for Handheld Radio Transceivers - The article highlights the common absence of modern USB-C ports on handheld ham radios and the limited use of USB for power. The author, [jephthai], shares a solution involving a USB-C cable with power negotiation capabilities, allowing the radio to be powered by USB. By splicing Anderson power pole connectors onto the cable, the radio can now be conveniently powered by a USB battery bank, providing a practical alternative to traditional 12 V batteries for off-grid operations.
    [ Hits: 141 | Votes: 1 | Rating: 10 ]
Technical Reference : Coax Cables and Connectors
  • Custom pigtail cable with Anderson PowerPole connector - In this post, we describe how to make a pigtail cable to connect the Kenwood TH-F6A triband HT to a 12Vdc power source via an Anderson PowerPole connector.
    [ Hits: 120 | Votes: 0 | Rating: 0 ]
  • How to assemble a BNC connector - How to install a BNC connector on a coaxial cable like the ELSPEC1030AF / HPF195RG and 58C/U cables
    [ Hits: 194 | Votes: 0 | Rating: 0 ]
  • Basics of Anderson PowerPole Connectors - How to build and secure Anderson Power Pole Connectors properly
    [ Hits: 145 | Votes: 1 | Rating: 2 ]
  • Everything You Need To Know About Coaxial Cable - An technical page on coaxial cables that describes what coax cables are, how do coax cables works, what are RG cables and difference with several coax cable types, what they are used for, connector types and cable sizes
    [ Hits: 157 | Votes: 0 | Rating: 0 ]
  • N-Type Connector on Cellflex Cable - Installation of Female N-Type Connector on 1-5/8 RFS Cellflex Cable
    [ Hits: 95 | Votes: 2 | Rating: 6.5 ]
  • Understanding Impacts of 75-ohm Devices in 50-ohm Systems - This article explores the implications of using 75-ohm devices, common in TV setups, within 50-ohm systems. While mismatched cables and connectors may lead to minimal consequences in receive-only setups, potential losses and reduced isolation in splitters and taps are examined. The article concludes that, for general applications, inexpensive TV-type components can offer reasonable performance with some trade-offs
    [ Hits: 145 | Votes: 2 | Rating: 9.5 ]
Technical Reference : Dummy Loads
  • Dummy Load Construction - This will document a custom version of the K4EAA Dummy load done using 20 1K ohm 3 Watt Resistors, Piece of brass sheet, a quart paint can and a BNC connector
    [ Hits: 186 | Votes: 1 | Rating: 5 ]
Technical Reference : Mic wiring
  • An Inexpensive Microphone Selector Switch - Take a commercially available switch box intended for switching data lines such as printer cables between two computers, and change out the connectors so that it can be used to switch between two microphones to one transceiver.
    [ Hits: 254 | Votes: 1 | Rating: 7 ]
  • Icom External Keypad Connector Cable - To connect the external keypad to your Icom radio you’ll need to make a connector cable like this.
    [ Hits: 95 | Votes: 1 | Rating: 1 ]
Technical Reference : Sound Card Radio Interfacing
  • Apple MacBook interface for digital modes - How to make a custom Line In connector for apple macbook or iMac to connect your amatur radio transceiver. A simple modification of a standard USB audio interface can work.
    [ Hits: 135 | Votes: 0 | Rating: 0 ]
  • Isolated PTT and CW Key interface - Simple soundcard interface that can satisfy several requirements like totally isolated AF interface, Totally isolated PTT and CW Key interface, Extend Accessory connector to interface to allow easy connection of TNC and provide a solid PTT or SEND connection
    [ Hits: 155 | Votes: 0 | Rating: 0 ]
  • Miniature CI-V for Icom Radios - With some fantasy the circuit can be easily assembled on a small scrap of pre-perf board,and then fitted in the DB9 serial connector shell. The interface requires two NPN transistors and few more passive components.
    [ Hits: 112 | Votes: 0 | Rating: 0 ]
Technical Reference : Transverters
  • Transverter for 50 70 28 MHz - This multiband transverter project features power output at 13,8V 50MHz 15W, 70MHz 10W, second harmonic <65dBc. Single N connector of antenna, suitable for a dual band Yagi. Article include Block Diagram for Dual Transverter and low pass filters
    [ Hits: 151 | Votes: 1 | Rating: 10 ]

Not satisfied ? Lookup Google Custom Search Engine for connector


Search connector with: Yahoo!, DuckDuckGo , Bing

Search

Related Searches

Get our links, Everywhere!

Follow us on Social Networks
RSS Feeds The DXZone.com RSS feed

Sign up for daily Newsletter

Service provided by Google FeedBurner

Free for your Site

Add our gadgets to your site
Daily Top 10 links

Google Custom Search