frequency adjust

frequency adjust

Antennas : Magnetic Loop

• Mastering Magnetic Loop Antenna Control - Unveil the secrets of efficient Magnetic Loop Antenna control systems, eliminating the hassle of frequent retuning. With real-time tracking and compatibility with various transceivers, including popular models from Elecraft, ICOM, Kenwood, and Yaesu, this controller ensures seamless frequency adjustment. Explore its high-resolution stepper motor and versatile communication capabilities, revolutionizing amateur radio operation.
  [ Hits: 54 | Votes: 0 | Rating: 0 ]

• Tenna Dipper Kit - The "Tenna Dipper" is a low power antenna analyzer and ATU tuning aid. With this handy accessory, you can determine the 50 Ohm resonance frequency of antennas or you can adjust your antenna tuner for a 50 Ohm match without generating QRM
  [ Hits: 4037 | Votes: 4 | Rating: 3.25 ]

• How To Make A VO-52 SAT QSO Video - Using a home made 10 element 435 & IO Loop for 145MHz, with a Yaesu FT-847. Simon - 2E0HTS, adjusts his (uplink) transmitted signal to correct the doppler of the Received (downlink) frequency.
  [ Hits: 1029 | Votes: 0 | Rating: 0 ]

• Frequency Calibration for Weak Signal Work - Accurate calibration of your receiver and sound card is necessary for good results with the weak signal modes in use at LF. Modern receivers with master oscillators that are synthesized to provide all conversion frequencies greatly simplify the process. This article describes a method of making the necessary measurements and adjustments to an ICOM R75 receiver and a sound card, using the ARGO software
  [ Hits: 873 | Votes: 1 | Rating: 7 ]

• Icom 706MK2G Repair - After years of reliable performance, a 26-year-old Icom 706MK2G exhibited an unusual deviation during FM transmission, with the actual frequency being 10kHz off from the displayed frequency. Additionally, the power meter showed a sharp dip during transmission. Upon investigation, it was discovered that the FM VCO voltage adjust variable had become dirty and sluggish over time. By adjusting the variable capacitor and cleaning it with switch cleaner, the issue was resolved, restoring stable power output and accurate frequency transmission.
  [ Hits: 18 | Votes: 0 | Rating: 0 ]

• ICOM IC-746PRO Frequency Calibration - Frequency calibration is a user adjustment on the rear panel. Learn how to calibrate the IC-746 Pro.
  [ Hits: 361 | Votes: 1 | Rating: 10 ]

• RX-PSK31 - Easy to use Audio Spectrum and PSK31 decoding program specially designed for SWL's who don't need TX or for anyone who just like to monitor PSK31 or analyse signals. Adjustable DSP and Spectrum settings for audio and frequency spectrum to set for best decoding of PSK31.
  [ Hits: 3110 | Votes: 12 | Rating: 7.41 ]
• RX-PSK31 - Easy to use Audio Spectrum- and PSK31 decoding program specially designed for SWL's who don't need TX or for anyone who just like to monitor PSK31 or analyse signals. Adjustable DSP and Spectrum settings for audio and frequency spectrum analasys or to set it for best decoding of PSK31 signals. By ON6MU
  [ Hits: 2960 | Votes: 2 | Rating: 10 ]

• KG-UV8D Programming Software - Wouxun KG-UV8D Standard Programming Software. Used to adjust or expand the frequency range to the full authorized range of the radio and not beyond. 134-174MHz 400-519MHz This software will Not add the 2.5kHz step.
  [ Hits: 581 | Votes: 7 | Rating: 9.29 ]

• Arduino QRP Transceiver: DIY Success on HF Bands - This article introduces an Arduino-based QRP CW Transceiver designed for lower HF bands. The journey begins with the Wotduino, evolving from a keyer to a multi-mode beacon. The development includes a QRP transmitter and culminates in a receiver inspired by Roy Lewallen design. The transceiver, controlled through a control bus features a signal path, modulation, filtering, and adjustable frequency settings. Despite initial testing intentions, successful QSOs on 80 and 40 meters showcase its functional capabilities.
  [ Hits: 109 | Votes: 1 | Rating: 1 ]

• Measured Data For HF Ferrite Chokes - FT-240 toroids measurements. The data was measured using well-calibrated HP instrumentation. All plots have been adjusted to a frequency range of 1-100 MHz on the horizontal axis and a resistance/impedance range of 10-1,000 ohms on the vertical axis. This adjustment facilitates comparison among different materials and aids in determining their suitability for use on the HF ham bands.
  [ Hits: 38 | Votes: 0 | Rating: 0 ]

• SDR Sharp Guide - Working with SDR#, adjusting frequency correction and basic setup.
  [ Hits: 2572 | Votes: 10 | Rating: 6.7 ]