os j pole

os j pole

Pages: [prev] 1 2 3 [next]

• Trapped Dipole for 12 and 17 Meters - A small sized and very cheap antenna project that allow you to work on WARC bands with a total gain very close to the dipole in both bands. On 12 meters is a normal dipole, while on 17 is a trapped dipole. Article in Italia
  [ Hits: 887 | Votes: 1 | Rating: 1 ]

• Squarooka Antenna - squared bazooka for 2 meters band - Sort of similar to the one of the 6m omni. Instead of using twin-lead, this design makes use of a more or less regular double bazooka antenna (coaxial dipole). Your attention shall be drawn to the available standart literature, such as Rothammel. In order to "compute" the dimension, Karl Rothammel mentioned that the total length of the dipole shall be 95% of the free-space wavelength. The short-circuit bridges (closing the folded dipole) are to be placed at a distance-fraction being equal to the velocity factor of the coax cable used, which will be 66% using RG-58 or RG174.
  [ Hits: 356 | Votes: 0 | Rating: 0 ]

• Postage Stamp 40 Meter Wire Dipole Antenna - Build yourself a postage stamp 40 meter wire dipole antenna that fits in a space a little over 20 wide and works reasonably well at low heights
  [ Hits: 2771 | Votes: 5 | Rating: 6.5 ]

• A Coax dipole for 4 m - This center-fed coaxial dipole for 4 mters feature low-cost components, Easy to set-up - nothing to adjust and no metalwork required, with only four soldered joints
  [ Hits: 553 | Votes: 1 | Rating: 10 ]
• A centre-fed co-axial dipole for 4-m - This design has the following advantages low-cost components, Easy to set-up - nothing to adjust, no metalwork required, and only four soldered joints!
  [ Hits: 554 | Votes: 1 | Rating: 10 ]

• The Ugly MacGyver 6 meter J-pole Antenna - Essentially, a J-pole is a 1/2 wave resonant antenna connected to a quarter wave matching stub. The feedline is connected at a point on the matching stub that is at the feedline's characteristic impedance. The result is 3/4 of a wavelength on one side and 1/4 wavelength on the other side.
  [ Hits: 202 | Votes: 0 | Rating: 0 ]
• Simple 50MHz J-Pole Antenna EA7AHG - Based on the popular DK7ZB simple 50 MHz Jpole antenna, this customized jpole project has been analized with MMANA-GAL and reproduced for six meters, two meters and 70 cm bands.
  [ Hits: 280 | Votes: 1 | Rating: 4 ]

• Shortened 80m Antenna - An antenna for 80 meters band for those who does not have enough space to setup a halwave wire dipole that is aprox 130ft or 40 meters. The antenna is an open-wire-fed shortened dipole
  [ Hits: 421 | Votes: 1 | Rating: 1 ]

• 20m Half-Wave End Fed - A Half wave antenna has a high impedance feed point. This can be matched using a 1/4 wave stub matching section and converts the 40m vertical into an L-shaped 20m J-Pole antenna. The 300 ohm feeder used for this purpose must be kept away from the ground.
  [ Hits: 1845 | Votes: 7 | Rating: 8 ]

• 20 thru 10 Meter Fan Dipole - The 20 thru 10 meter dipole is constructed from stranded insulated wire available in most hardware stores. The feedpoint uses an 8 inch long section of 2 inch diameter PVC pipe. A section of wire joins the elements at either side of the feedpoint to avoid the inductance of square knots used on lower frequencies.
  [ Hits: 3181 | Votes: 14 | Rating: 5.96 ]

• Choosing right material to make antennas - Why build antennas out of copper and not aluminum or stainless steel. Selecting the best metals for antennas evaluating the conductivity factor.
  [ Hits: 336 | Votes: 2 | Rating: 5.5 ]

• Home Brew J-Pole Antenna Project - Building a two metre J-Pole Antenna
  [ Hits: 856 | Votes: 0 | Rating: 0 ]
• J-Pole Construction Drawings - Complete plan for making a 2-meter J-Pole antenna. This drawing in PDF File includes a detailed list of the parts needed to assemble the Jpole antenna for 144 MHz.
  [ Hits: 256 | Votes: 3 | Rating: 4 ]

• ZS6KMD 20-40m Multiband Dipole - The dipole shown in this document is installed in an inverted Vee configuration, with two leg elements on each side held parallel to each other by 21cm spacers. The upper leg is for 40m and the lower leg for 20m. The spacers are made of 7mm plastic garden hose support for garden sprayers cut to 21cm.
  [ Hits: 532 | Votes: 0 | Rating: 0 ]

• OCF Dipole - This is a popular antenna design as the performance is very good across the HF bands and requires little or no tuning. It is a dipole fed off center with a 4:1 current balun at the offset feedpoint. The antenna shown covers 80, 40, 20 and 10 meters with 15 meters and WARC bands
  [ Hits: 2559 | Votes: 7 | Rating: 9.43 ]

• Portable wire antennas - This document describe serveral wire antennas, from the folded dipole, to the common halfwave monoband antenna for those who want to make HF portable operations in holiday.
  [ Hits: 844 | Votes: 2 | Rating: 1 ]

• The Tilted Terminated Folded Dipole - T2FD A practical construction article, which first appeared in the Electronic DX Press, contains a number of useful photos and detailed instruction to build this antenna by VK3BVW
  [ Hits: 1180 | Votes: 3 | Rating: 4 ]

• VHF / UHF Antenna Design - A dipole for 2m, 4m, 6m band an hamdwritten note for a homemade vhf antenna that can be tuned across the VHF band
  [ Hits: 1695 | Votes: 10 | Rating: 7.08 ]

• W8JK Beam Antenna - The W8JK is a famous and effective DX antenna, first built by John Kraus, W8JK, in 1937. A Beam antenna with two parallel dipoles driven with opposite phase, with a close spacing of an eighth of a wavelength.
  [ Hits: 5151 | Votes: 21 | Rating: 7.19 ]

• Custom pigtail cable with Anderson PowerPole connector - In this post, we describe how to make a pigtail cable to connect the Kenwood TH-F6A triband HT to a 12Vdc power source via an Anderson PowerPole connector.
  [ Hits: 121 | Votes: 0 | Rating: 0 ]

Pages: [prev] 1 2 3 [next]