pvc dipole

pvc dipole

Antennas : 160M

• 160 Meter Dipole - The 160 meter dipole is constructed from #12 stranded insulated wire available in most hardware stores. The feedpoint uses a section of PVC pipe Article by W1TR
  [ Hits: 1116 | Votes: 2 | Rating: 6 ]

• 20 meters rigid dipole - Rigid Dipole antennas for 14 MHz band using PVC and Aluminium tubing
  [ Hits: 7011 | Votes: 14 | Rating: 6.57 ]

• A simple 2 meter antenna - A simple center-fed dipole made just with a thin-wall PVC pipe, aluminum tape, and RG-8X coax
  [ Hits: 1497 | Votes: 2 | Rating: 5.5 ]
• VHF sleeve dipole antenna - An off-center-fed sleeve dipole, made of CPVC and aluminum foil tape by KV5R
  [ Hits: 806 | Votes: 0 | Rating: 0 ]

• 30m vertical dipole - The 30 Meter Vertical Dipole is constructed from #10 stranded insulated wire available in most hardware stores. The feedpoint uses a T-section of PVC pipe. The coax loops through the PVC pipe to provide strain relief. by W1TR
  [ Hits: 2050 | Votes: 2 | Rating: 4.5 ]

• Trapped dipole for 40-80-160 meters  ^pop - Build a space efficient trapped dipole antenna for 40-80-160 meter bands using RG-58 and PVC pipe by W8NX
  [ Hits: 96972 | Votes: 119 | Rating: 6.24 ]
• 40m loaded dipole - This is an short dipole for 7 MHz. Total length of this dipole is just 10 meters, 33 feet. Missing lenght is balanced by a coil made of 49 turns of a 40mm diameter pvc pipe. The use of a choke balun is recommended, as always, to adapt the unbalanced coax cable to the balanced antenna, and to prevent RF feed back along the coax shield.
  [ Hits: 194 | Votes: 4 | Rating: 8.75 ]

• W3FF Portable Dipole - This is the antenna w3ff designed for his walking portable station. It is a dipole constructed out of the plastic plumbing pipe CPVC. There are telescoping whips at the ends of each side of the dipole, and these whips are adjusted to bring the antenna into resonance on each of five HF Bands 10, 12, 15, 17, and 20 Meters
  [ Hits: 22068 | Votes: 14 | Rating: 8.13 ]
• Center Connector for Dipole Antenna - This is another alternative home-brew center connector for a dipole. The parts used are common PVC accesories found at the home supply store.
  [ Hits: 861 | Votes: 3 | Rating: 10 ]

• 20 thru 10 Meter Fan Dipole - The 20 thru 10 meter dipole is constructed from stranded insulated wire available in most hardware stores. The feedpoint uses an 8 inch long section of 2 inch diameter PVC pipe. A section of wire joins the elements at either side of the feedpoint to avoid the inductance of square knots used on lower frequencies.
  [ Hits: 3182 | Votes: 14 | Rating: 5.96 ]

• Picture of a multiband dipole  ^pop - Pictures of a multiband dipole, build with simple PVC T and standard electrical wire
  [ Hits: 41088 | Votes: 25 | Rating: 4.77 ]

• OCF 2-Meter Sleeve Dipole Antenna - A 144 MHz dipole antenna made from coax, PVC pipe, and aluminum foil tape
  [ Hits: 3092 | Votes: 7 | Rating: 4.85 ]

• 2.6 MHz Halfwave Sloper - The 2.6 Mhz M Dipole is constructed from #10 stranded insulated wire available in most hardware stores. The feedpoint uses a T-section of PVC pipe
  [ Hits: 386 | Votes: 0 | Rating: 0 ]