rf coil

rf coil

Antennas : 160M

• K6MM 160m Antenna Modifications - After a storm damaged the antenna, W6AER replaced it with a pre-made capacitance hat from DX Engineering. Using hose clamps and conductive grease, he ensured durability. Experimenting with radials and a coil, he aimed for better performance and resilience.
  [ Hits: 46 | Votes: 0 | Rating: 0 ]

• The Vertical Buddi Beam for 20m - The Vertical Buddi Beam on 20m using no Coils. n this article I am going to describe a totally new way to construct and use a very old design the two element Yagi antenna. Unlike the traditional Yagi this design does not require a Tower or a boom, it is 100 percent portable and most important high- performance and easy to assemble using standard Buddipole components.
  [ Hits: 580 | Votes: 2 | Rating: 4.5 ]

• 40m loaded dipole - This is an short dipole for 7 MHz. Total length of this dipole is just 10 meters, 33 feet. Missing lenght is balanced by a coil made of 49 turns of a 40mm diameter pvc pipe. The use of a choke balun is recommended, as always, to adapt the unbalanced coax cable to the balanced antenna, and to prevent RF feed back along the coax shield.
  [ Hits: 194 | Votes: 4 | Rating: 8.75 ]

• A very efficient half size 40 meter Vertical Antenna - A vertical antenna project for the 7MHz made with some spare parts. Based on a broken 20 foot fishing pole, it is based on a good ground system made with radials and a capacitive hat done to increase the global radiation resistance of the antenna. A custom loading coil is also included in this project to perfectly tune the antenna to the CW portion of the 40 meters band.
  [ Hits: 736 | Votes: 4 | Rating: 8.5 ]

• 80m Shortened Dipole Antenna - This antenna just requires about 24m of free space instead of 41m that a normal half wave 80m antenna needs to hang up. The so called loaded dipole uses a coil in every dipole arm to electrically lengthen the mechanical too short dipole arms. Every coil has an inductivity of 120 microHenry.
  [ Hits: 154 | Votes: 0 | Rating: 0 ]

• Antenna Matching Coil Adjustment Procedure - Without this basic knowledge, addressing antenna problems, RFI problems, and matching problems, results in a frustrating situation. Procedure which must be followed to properly adjust a shunt matching coil.
  [ Hits: 2678 | Votes: 4 | Rating: 4 ]
• RF Choke Coil - Made Easy - In this article K3DAV show a very simple way to make an RF choke coil that will remove your RF feedback troubles
  [ Hits: 1266 | Votes: 6 | Rating: 5.83 ]

• Build your own RF-Choke - How to make an effective RF Choke. The coiled coax choke is the easiest to make but also the least effective. This article includes some general guidelines for winding coax chokes on a 10cm PVC pipe using RG-58 or RG-213 coax cable.
  [ Hits: 794 | Votes: 12 | Rating: 7.33 ]

• DIY Portable Car Whip Antenna - Being frequently away from home, the author owner of an Elecraft KX3 missed the opportunity to work /M. They devised a portable antenna solution, incorporating a coil and car body, enabling multi-band tuning. Despite its unconventional design, the antenna exhibits promising performance, resembling a vertical dipole.
  [ Hits: 54 | Votes: 0 | Rating: 0 ]

• Petlowany Antennas by K6NO - WorldRadio Article on Petlowany antennas base on this principle: if a length of wire is wound into a spiral-shaped coil and excited by a radio frequency current connected to the innermost portion of the coil, it will then, and only then, exhibit RF characteristics that closely approximate those of a resonant linear wire of the same length
  [ Hits: 3766 | Votes: 9 | Rating: 6.22 ]

• The Squid Pole Wire Antenna Re-visited - The author explores enhancing the performance of a 7-meter fiberglass squid pole wire antenna for amateur radio. The wire, resonant at 10MHz, poses impedance challenges on various bands. Experimenting with direct coax feed and UN-UN transformers, the LDG Z11-Pro2 auto-tuner is found effective but may show deceptive SWR readings. The author employs adjustable UN-UN ratios and introduces a custom "porcupine" coil to optimize the antenna's efficiency.
  [ Hits: 91 | Votes: 0 | Rating: 0 ]

• CWS Coil Winding Specialist - Manufacturer of transformers, inductors coils and chokes. Custom winding, EMI / RFI Filters, Antenna Windings on ferrite rod, Antenna Winding on phenolic. Any antenna coil designs.
  [ Hits: 593 | Votes: 1 | Rating: 1 ]

• BG Micro - All kind of electronic components, Hobby Electronics and Parts, motors, Sun power solar panels, switches, rechargeable batteries, RF Coils, Coils and Chokes
  [ Hits: 727 | Votes: 0 | Rating: 0 ]
• Communication Coil - Communication Coil, Inc. designs and produces custom, high reliability Filter Networks, RF Coils, Chokes, Inductors, Baluns, Toroids and Power Magnetics for communications
  [ Hits: 807 | Votes: 0 | Rating: 0 ]

• Hamtech - HAM-made engineering products supplies and produces coaxial relays, antenna switches, sequencers, roller inductors, variable capacitors, low noise preamplifiers, RF power rotary switches and coil bodies.
  [ Hits: 192 | Votes: 0 | Rating: 0 ]

• TANT 136 - DOS program for calculating the performance of a T antenna. Gives loading coil info and matching plus ERP by Reg G4FGQ
  [ Hits: 531 | Votes: 2 | Rating: 2.5 ]

• BITX QRP RTX - An easy to build 6 watts SSB transceiver for 14MHz. BITX is an easily assembled transceiver for the beginner with very clean performance. Using ordinary electronic components and improvising where specific components like toroids are not available, It has a minimum number of coils to be wound.
  [ Hits: 104 | Votes: 0 | Rating: 0 ]