software for pc

software for pc

Pages: [prev] 1 2 3

• SWR ANTENNA ANALYZER + WSPR TX - Available worldwide can be used as Arduino Shield or plug it in to you PC , or with a bluetooth adapter connect to Android. With a highly optimized software, KAI200 brings you: a. Antenna analyzer form 1 up to 200 Mhz; b. WSPR transmiter (set up by serial terminal); c. Square Wave Signal generator KAI200 is all you need for your radio whatever it is Yaesu, Icom, Kenwood or Drake and DIY projects.
  [ Hits: 327 | Votes: 8 | Rating: 9.62 ]

• IC7300BKT Icom IC-7300 CAT Control - Windows PC control program for the Icom IC-7300 transceiver. Power-on and Power-off by software BktNetInterface for JTDX and WSJT-X, audio recording, memory management, cw keyer management, Interface for other software
  [ Hits: 463 | Votes: 2 | Rating: 7 ]

• DesignSpark PCB - DesignSpark PCB is the world's most accessible electronics design software, specially designed for Rapid Prototyping and turning your circuit ideas into testable boards faster. Easy to learn and easy to use, DesignSpark PCB is free and can you can download DesignSpark from this site.
  [ Hits: 526 | Votes: 0 | Rating: 0 ]
• PCB gEDA - PCB is an interactive printed circuit board editor for Unix, Linux, Windows, and Mac systems. This Software runs across multiple platforms such as Unix, Linux, Windows as well as Mac systems. This Tool is widely used for electronics as well as electrical circuit designing that comes with schematic capture. PCB offers high end features such as an autorouter and trace optimizer which can tremendously reduce layout time.
  [ Hits: 104 | Votes: 0 | Rating: 0 ]

• MLOG - MLog is a legacy freeware hamradio logging software for windows. It has been tested on Windows XP, written by hams for hams. Even if outdated can easily run on older PCs.
  [ Hits: 137 | Votes: 0 | Rating: 0 ]

• GBCAT - GBCAT is free PC software for controlling amateur radio devices through a COM/USB port or through a TCP/IP network, with the ability to transfer a 2-way audio signal over a TCP/IP network supporting Yaesu FT-857 FT-817 FT-897, Icom IC-706MKIIG, Kenwood TS-2000 and TS-590S by 9A2GB.
  [ Hits: 2528 | Votes: 44 | Rating: 9.14 ]

• Dream DRM Receiver - Open-Source Software Implementation of a DRM (Digital Radio Mondiale) Receiver. Dream runs on virtually any pc and requires a receiver front-end to work as a real radio.
  [ Hits: 1070 | Votes: 3 | Rating: 10 ]

• Automatic antenna switch with Arduino Nano - Arduino Nano board based antenna coax antenna switch intended for use with ICOM CI-V protocol. When is used alone with transceiver without PC control (CAT software, any logging software with CAT functionality), the CI-V transceive option in TRX setup shall be set to ON.
  [ Hits: 141 | Votes: 1 | Rating: 9 ]

• MiniTioune receiver project - The MiniTioune receiver project, developed by Jean-Pierre F6DZP, consists of the home constructed MiniTiouner hardware which interfaces via a standard USB 2.0 port to a Windows PC running the MiniTioune software. It can be used to receive satellite broadcasts transmissions making it ideal for use on Q-oscar 100 Es hail-2 without any external frequency converters.
  [ Hits: 197 | Votes: 0 | Rating: 0 ]

• Tulip SDR - SDR Project for a compact amateur radio software defined radio trasceiver covering HF bands all mode. Website includes schematics, element PCB, pictures, movies, firmware and elements bom.
  [ Hits: 369 | Votes: 5 | Rating: 8 ]

• How RTL-SDR dongles work - Since 2012, the RTL-SDR is the simple and cheap way to give Software-Defined Radio a try. For about 25 euro you get a receiver covering much of the VHF and UHF range, and by either adding an upconverter, or using the direct sampling option, also the HF bands. They are so cheap because they are mass-produced as DVB-T receivers.
  [ Hits: 129 | Votes: 1 | Rating: 10 ]

• Connect you MacOS to CAT Serial Port - How to connect an Apple MacOS to a USB Radio transceiver. Get a Mac driver for ICOM IC-7100, IC-7200, IC-7300, IC-7600, IC-7610, IC-7850, IC-9100, PCR2500, Kenwood TS-890S, TS-990S, TS-590S, Elecraft KX3, K3S, Yaesu FTdx3000, FT-891, FT-991 or Ten-Tec Eagle USB direct connect built in USB/Serial adapter.
  [ Hits: 230 | Votes: 0 | Rating: 0 ]

Pages: [prev] 1 2 3