transmit id

transmit id

Pages: [prev] 1 2 3 4 5 [next]

• 40m Wire Antennas Comparison - On the field comparison among C-Pole antenna, an EFHW vertical antenna and an Inverter V dipole antenna. Test is done using two identical WSPRLite beacons that transmit with 200mW on the WSPR frequency and analyzing spotted results.
  [ Hits: 172 | Votes: 1 | Rating: 3 ]

• VHF Baluns: Fact and Fancy - Our ideas about HF baluns have changed dramatically in recent years. The focus today is very much on suppressing unwanted common-mode RF currents, to reduce both the received noise levels and the risks of causing interference on transmit.
  [ Hits: 283 | Votes: 0 | Rating: 0 ]

• Cloverleaf Antenna - Cloverleaf antenna is a circular polarized antenna which is way better than the cheap dipole antenna that comes with video transmitters and receivers. The Cloverleaf is a closed loop antenna which the signal and ground wires are connected. The cloverleaf antenna has 3 loops at 120 degree apart, and they are titled at 45 degree to horizontal plane.
  [ Hits: 64 | Votes: 0 | Rating: 0 ]

• World of Receivers and Transmitters - A searchable database of online websdr receivers, lists OpenWebRX, KiWi SDR and WebSDR from all over the world, providing a web interface to search and filter links to websdr
  [ Hits: 307 | Votes: 3 | Rating: 4 ]

• SWR ANTENNA ANALYZER + WSPR TX - Available worldwide can be used as Arduino Shield or plug it in to you PC , or with a bluetooth adapter connect to Android. With a highly optimized software, KAI200 brings you: a. Antenna analyzer form 1 up to 200 Mhz; b. WSPR transmiter (set up by serial terminal); c. Square Wave Signal generator KAI200 is all you need for your radio whatever it is Yaesu, Icom, Kenwood or Drake and DIY projects.
  [ Hits: 327 | Votes: 8 | Rating: 9.62 ]

• Guide to DMR Code Plugs - Basic information on code plugs. What code plugs is, how to set up a code plug, transmit talk groups and configuring zones.
  [ Hits: 180 | Votes: 1 | Rating: 10 ]

• Ribbit digital text messaging mode for HF/VHF/UHF - Ribbit is a novel digital text messaging mode for VHF/UHF communications for recreational and emergency use which radically increases the density of information transmitted by spectrum used. It leverages the computing power of the modern smartphone to increase the capabilities of any Handy Talkie without requiring any additional hardware or cable. A Ribbit message is fixed in duration at 1250 milliseconds. It is sent over audio modulation with a 2kHz bandwidth centered on 1.5kHz. It is preceded by 400ms of white noise to open analog squelch circuits.
  [ Hits: 133 | Votes: 1 | Rating: 10 ]

• FT8 and splatter and the ugliness of ALC - A guide to properly use FT8 ALC and power when transmitting in FT8 Mode. Incorrect usage of power and audio from your computer may cause unreadable signals and transmit harmonics that can didturb other signals.
  [ Hits: 391 | Votes: 1 | Rating: 1 ]

• PSK: How to Assure a Clean Signal - Due to the nature of PSK it is imperative that you maintain a very clean signal. In this page you will find examples of a clean PSK signal and one with excessive splatter, and a short guide on how to properly adjust your transmitter to assure a clean trace
  [ Hits: 137 | Votes: 0 | Rating: 0 ]

• N6QAB Hidden Transmitter Controllers - When it is time for you to hide a Hidden Transmitter there are several ways to control the transmission timing and audio of the transmitter.The most basic of these is of course the manual method of hiding in the bushes with your trusty HT and talking on and off for several hours.
  [ Hits: 61 | Votes: 0 | Rating: 0 ]

• IC-7300 Bluetooth Support - It is possible to add a very small Bluetooth transmitter to the 3.5mm headphone jack and then use a pair of Bluetooth headphones around the shack. In this article Author provides some tips on choosing the proper Bluetooth interface.
  [ Hits: 286 | Votes: 4 | Rating: 7 ]

• DCF77 - DCF77 is a time signal transmitter operated by the Physikalisch-Technische Bundesanstalt (PTB). It broadcasts on a frequency of 77.5 kHz and is widely used for time synchronization in Europe.
  [ Hits: 57 | Votes: 1 | Rating: 10 ]

• Antenna Switch - An home made antenna switch with a Dummy Load selector. If you forget the radio is connected to the open or grounded side of the switch and you try to transmit, it is very easy to damage the finals of your transceiver.
  [ Hits: 321 | Votes: 3 | Rating: 8 ]

• The G4AON SSB Transmitter - This transmitter covers the 160, 80, 40 and 20 metre bands and provides both SSB and properly generated CW. The CW side of this transmitter is not compromised and produces excellent CW. On SSB the audio has been tailored to provide a rising response to 3 KHz, with a sharp drop above that frequency. There is RF speech clipping to both provide more "punch" and to limit the peak output.
  [ Hits: 181 | Votes: 2 | Rating: 9.5 ]

• Preventing CW key clicks - Key clicks are generally undesired clicks or thumps generated by a CW transmitter as the key is put down or let up. How much does the rise time or bandwidth of a CW signal need to be limited to prevent other QSOs on adjacent frequencies from being annoyed by key clicks?
  [ Hits: 93 | Votes: 0 | Rating: 0 ]

• APRS LoRa Weather Station - The weather station described here uses a TTGO v3 1.6.2 module and various sensors. It displays the data on an OLED screen and transmits them among a choice of protocols to the APRS, APRS-IS, Wunderground servers or via an MQTT broker. APRS data is transmitted on 433.775 MHz (can be changed) using the LoRa protocol. APRS beacons picked up by iGate gateways are then transmitted to APRS servers.
  [ Hits: 108 | Votes: 0 | Rating: 0 ]
• LoRa in Amateur Radio - About LoRa, wireless communication technology designed to transmit data over long distances. LoRa provides a means for wireless data transmission over long distances with low power consumption. Practical applications of LoRa in amateur radio
  [ Hits: 102 | Votes: 0 | Rating: 0 ]

• rpitx Multimode TX for Raspberry Pi - rpitx is a general radio frequency transmitter for Raspberry Pi which doesn't require any other hardware unless filter to avoid intererence. It can handle frequencies from 5 KHz up to 1500 MHz.
  [ Hits: 279 | Votes: 0 | Rating: 0 ]

• Arduino Repeater Controller - This blog article introduces an updated repeater controller project utilizing the Arduino UNO. It includes a CW identifier, and the ID message can be customized using hex codes. The author offers a Windows command line program for easier message coding and provides a link for download. The controller features three adjustable timers for IDer, Timer-out, and Squelch-tail. The article also mentions the use of an audio switch to control audio levels between the receiver and transmitter. Detailed instructions and code files are available on the author's website for both version 1 and version 2 of the Arduino repeater controller. The project aims to enhance repeater functionality and audio management in ham radio operations.
  [ Hits: 94 | Votes: 0 | Rating: 0 ]

• Simple 2-tone generator - A simple 2-tone-generator for testing the linearity of SSB transmitters. This device is as simple as useful. With 2 transistors and an oscilloscope, it is fairly easy to test the linearity of your SSB transmitter. The 2-tone-method is a standardized test method that can be used to determine the maximum output and the amplification characteristics of a sideband transmitter.
  [ Hits: 111 | Votes: 0 | Rating: 0 ]

Pages: [prev] 1 2 3 4 5 [next]