tubing

tubing

Pages: [prev] 1 2

• Dual Band Wire Beam 12 and 17 m - The Dual-Band Wire Beam was inspired by L.B. Cebik's (W4RNL) article The Elusive Moxon Nest. Fiberglass tubing spreaders, Flexweave elements, an aluminum hub, and two die-cast aluminum flanges combine to provide a 12/17m Moxon nest with one 50 ohm feed.
  [ Hits: 3649 | Votes: 2 | Rating: 10 ]

• 30m Half -Size Rotary Dipole - A rotary dipole antenna for 30 meters band. Each arm is about 12.5 ft and is constructed from telescoping fibreglass flag/fishing poles and short lengths of aluminium tubing. Two short lengths of glass-fibre rod were used to insulate the arms from the supporting hardware.
  [ Hits: 198 | Votes: 0 | Rating: 0 ]

• 40 meter cage dipole - The antenna consists of 6 runs of stranded wires spaced by plastic Hula Hoop spacers made of poly tubing
  [ Hits: 895 | Votes: 2 | Rating: 9 ]

• Six meter dipole project - Design and build an 6 m dipole antenna from aluminum, tubing, that resembles the active element of a yagi beam antenna.
  [ Hits: 900 | Votes: 1 | Rating: 9 ]

• 6 Meter Band Moxon Style Antenna - Design and build a 6 meter 2-element Moxon antenna mostly from available aluminum tubing and angle stock.
  [ Hits: 616 | Votes: 1 | Rating: 1 ]

• Homebrewing a 6 Meter Yagi - In this PDF article Zack Lau describe how to homebrew a four element yagi beam antenna for 50 MHz band, including how to build mounting blocks and tubing clamps to hold elements.
  [ Hits: 966 | Votes: 2 | Rating: 5.5 ]
• A portable 3 element 6m Yagi  ^new - A small Yagi antenna for camper van. It is made of aluminum tubing, breaks down for storage, and works well for communicating with others. He built it in an afternoon and it gets good signal. The antenna is lightweight and can be packed up to fit inside his van while traveling
  [ Hits: 38 | Votes: 0 | Rating: 0 ]

• Winding Inductors on Cantex 4 Inch PVC Tubing - Coil winding on 4 inch PVC tubing with home-made tooling.
  [ Hits: 628 | Votes: 0 | Rating: 0 ]

• Amateur Antenna Tripod - This project produces a sturdy tripod for small vertical antenna support using readily available electrical metal tubing (EMT) or conduit
  [ Hits: 978 | Votes: 3 | Rating: 1 ]

• Slim Jim Aluminium - The 2 Meter 146mhz Slim Jim Antenna using aluminum tubing!
  [ Hits: 1113 | Votes: 1 | Rating: 4 ]
• 2 Meter Slim Jim Antenna - A 144 Mhz Slim Jim Antenna, aluminum tubing version project by Mohammad 9W2WTF
  [ Hits: 1025 | Votes: 1 | Rating: 10 ]

• Quarter Wave 80 m vertical Antenna - Homebrew a 1/4 wave 80 meter vertical using aluminium tubing
  [ Hits: 2437 | Votes: 6 | Rating: 7 ]

• Eidolon AS - Antenna element holders, antenna parts, aluminium tubing, fiberglass tubing, connectors and antenna mounts and hardware by Eidolon AS
  [ Hits: 711 | Votes: 2 | Rating: 1 ]

• Maple Leaf - Located in southern Ontario Canada, supplier for HF VHF antenna kits, aluminium tubing, portable j-pole antennas, lightning suppressors, connectors and adapters
  [ Hits: 1389 | Votes: 0 | Rating: 0 ]

• Lightning protection system - A tower grounding project using copper tubing to help protecting an antenna tower by WD0M
  [ Hits: 465 | Votes: 0 | Rating: 0 ]

• Baofeng UV5R TRRS Adapter - A tiny board, which allows a smartphone or similiar device to connect to the Baofeng UV5R radio via a TRRS audio connector. It allows for connecting the radio to a software TNC app such as APRSDroid or PocketPacket. Solder on the components, solder on the cables, then provide some stress relief, (I use solid-core wire and heat shrink tubing), and you can use your UV5R with your smartphone for APRS on the cheap.
  [ Hits: 91 | Votes: 0 | Rating: 0 ]

Pages: [prev] 1 2