wireless network

CardboardHorn - Seattle Wireless - A Cardboard Horn antenna for 802.11b

The L‐Network Impedance Matcher - N6LYU Greg article on L-Network

Dish 802.11 Wireless Networking Antenna - This antenna modification is for the IEEE 802.11b networking protocol that operates at 2.4 GHz. It can be scaled easily to the 5 GHz frequency used by IEEE 802.11a by simply scaling the dimensions on the feed can and the excitation antenna to 2.4/5 = 48% of the dimensions shown above.

2.4 Ghz double quad antenna  ^pop - An easy to build, compact antenna for wireless lan applications that offers a reasonable amount gain.

Pringles Yagi Antenna - Design and build a Pringles Yagi antenna for 2.4Ghz.

Building Helical Antennas - Seattle Wireless - Photos and comments on building an helical antenna for wifi

DirectionalWaveguide - Seattle Wireless - Waveguide antenna is a type of DirectionalAntenna and is a modified waveguide. A waveguide is simply a tube, either rectangular or cylindrical in cross-section, that will carry a microwave radio signal with very low signal loss

PringlesCantenna - Seattle Wireless - The PringlesCantenna is an ultracheap Yagi-type directional antenna that can be built for under $10. The original Pringles Yagi was designed by Andrew Clap.

SardineCanAntenna - Seattle Wireless  ^updated - Sardine Can Antenna. is a BiQuad or Bi circle - wire length each side (8 x 1/4 waves ) 31 mm

DirectionalBiQuad - Seattle Wireless - A biquad is a fairly powerful antenna which is relatively easy to construct, with impressive performance for their size. A link greater than 5 miles can be made with a pair of these as a stand-alone antenna and a Prism2 100mW card, provided you keep coax short, and your line-of-sight is clear.

MicroTV Aerial - Seattle Wireless - Yagi antenna for 2.4Ghz band

2.4GHz Cubic Quad Antenna  ^pop - The Cubic Quad antenna is a commonly homemade antenna in the range of about 150 odd MHz. Our little project was to design one of these for use in the 2.4GHz range for 802.11 wireless LANs.

Wifi: Building Yagi Antennas - Example and resources of 2.4 Ghz yagi antenna plans

Bavarian Packet Radio Group - This site provides information about the BayCom packet radio hard- and software for radio amateurs. It also contains general information on the German packet radio network.

SSB Electronic USA - manufactures and distributes HF, VHF, UHF and SHF equipment covering 10MHz. - 47.0GHz. Our products include: Wireless LAN / WAN Bidirectional Linear Amplifiers, Low Noise Preamplifiers - LNA's, RF Linear Amplifiers, Relays, Transverter Systems, Frequency Translation Systems, Downconverters, Antennas, Parabolic Dishes, Coaxial Cable, Relays, Antenna Switches, Microwave Test equipment, PC controlled Receivers, Microwave Linear Amplifiers including models for Telemetry, Wireless, and CDMA applications.

Cantenna Wireless Booster Antenna - Extend the range of wireless network or connect to other wireless networks in neighborhood with your own wifi antenna.

PI-EL - The Windows program for designing and analyzing PI and PI-L networks by Tonne Software

IP-Sound  ^pop - IP-Sound is a Free application for audio exchange client to client over a TCP/IPv4 network (Lan/Internet). The main purpose for the existence of IP-Sound is to provide low quality audio 8-16kHz, with low latency for use together with remote control software for "ham" radio amateur equipment. IP-Sound is developed by SM5VXC.

Beacons - The W6AMT Beacons is a Windows program which automates the collection of radio propagation data. HF data is collected by monitoring the worldwide network of NCDXF / IARU HF beacons.

Elsie - Filter Design - Filter design software. Elsie is an uncommon commercial-grade lumped-element ("L-C") electrical filter design and network analysis program, directed toward the engineer or technician involved in that line of work.

Quad - from Tonne Software - This graphics-intensive program designs and analyzes active quadrature ("90-degree") networks for use in SSB transmitters and receivers.

RevLoad - This graphics-intensive program reveals the load on the output of a matching-network, based on measurements of the components in that network. Adjust the network (tuner) for a flat input, measure or look up the network component values and you will immmediately see the R and jX values of the load on the network, presented as both a schematic with the component values and as a Smith Chart normalized to the specified system impedance.

G3YXM 500 W solid state amplifier - HF 500 Watt power amplifier schematics by G3YXM

G3YXM 500 W PA - 40-80-160 meter band linear amplifier

RFI From Computer Networks - Is your router shutting you down ?