|
Search
|
 |
1 to 1 balun
53 links
and 2 categories
about 1 to 1 balun on dxzone.com
|
Result Page: 1 2 3 [>>]
Categories
Antennas : Baluns : 4 to 1 balun
Antennas : Baluns : 1 to 1 Balun
Site listings
Antennas : Baluns
- Baluns: theory and projects
pop
- All about baluns with photos, projects and instructions, by IZ7ATH
[Hits: 45575 | Votes: 36 | Rate: 6.45] - A better antenna-tuner balun
pop
- Which balun to use? The hybrid balun promises
advantages over both voltage and current baluns by ZS1AN
[Hits: 17773 | Votes: 11 | Rate: 5.83] - WB6ZQZ 3 in 1 Balun
- Builing a triple ration balun, that match resonant antennas from 9 ohms to 75 ohms with 1.5:1 or less SWR
[Hits: 3386 | Votes: 2 | Rate: 10.00] - Balun construction
pop
- PDF files describing how to homebrew a 1:2.5 balun
[Hits: 2 1355 | Votes: 27 | Rate: 7. 14] - Building baluns
pop
- How to easily home-brew baluns even in strange formats 1/1 - 2/1 - 4/1 - 6/1 - 9/1 - 12/1 et 16/1 for bands from 1.8 to 30 (50) MHz in french
[Hits: 223 12 | Votes: 13 | Rate: 7.00] - OH7SV Windom baluns
- Windom baluns for kilowatt range made with two ferrite toroidal cores amidon ft-140-61 and another schema with two ferrite rods
[Hits: 2350 | Votes: 4 | Rate: 8.50] - WB6ZQZ Triple Ratio Balun
- This balun matches resonant antennas from 9 to 75 ohms without a tuner and provides RF isolation to keep the current off the transceiver case
[Hits: 148 1 | Votes: 2 | Rate: 5.00] - The Ugly Balun
- A 1:1 choke balun for 160 thru 10 meters using one continuos lenght of coax to rig.
[Hits: 4444 | Votes: 5 | Rate: 6.60] Antennas : Baluns : 1 to 1 Balun
- A Cost Effective Current-mode 1:1 Balun
- A cost effective current-mode 1:1 balun can be constructed from a length of coax and a rod typically used for a broadcast antenna loop-stick, some electrical tape, cable ties, a length of PVC water-pipe and some connectors.
[Hits: 4734 | Votes: 1 | Rate: 10.00] - Low cost 1:1 balun
- A balun don't depend on use of ferrite beads, but use steel wool to attenuate any RF on the outer braid
[Hits: 37 10 | Votes: 1 | Rate: 1.00] - Simple HF Baluns for 50/75 ohm coax
- Show diagrams, winding methods and tables of some 1:1 and 4:1 baluns for 1.8 - 30 MHz suitable for use up to 200W (400W peak) on systems using 50 or 75 ohm coaxial cable input where SWR should not exceed 1.6:1.
[Hits: 6659 | Votes: 4 | Rate: 6.25] - Practical Guanella 1:1 balun
- This article proposes a lossy transmission line model of a practical Guanella 1:1 balun that is effective for all frequencies within and immediately adjacent to the pass band
[Hits: 2390 | Votes: 0 | Rate: 0.00] Antennas : Baluns : 4 to 1 balun
- How To Make A Homebrew 4:1 Balun
pop
- I built a homebrew 75 meter Double Extended Zepp Antenna, And I needed a 4:1 Balun So I decided to Homebrew the Balun also. Here is how I did it!
[Hits: 73682 | Votes: 92 | Rate: 6.2 1] - W1CG Low Power Balun Kit
- Contruction manual to build a 4:1 balun, it has good performance from 160 through 10 meters.
[Hits: 3078 | Votes: 3 | Rate: 9.00] - ZS6KMD Nescafe 4:1 Balun
- Making a 4:1 balun with a nescafe coffee jar lid and a toroid
[Hits: 3 17 1 | Votes: 2 | Rate: 4.00] - Homebrew A 4 To 1 Balun
- How to build a to 1 balun by N1HFX
[Hits: 6677 | Votes: 7 | Rate: 7.85] - A model of a practical Ruthroff 1:4 balun
- The 1:4 balun is of particular interest because it underlies many other configurations, and understanding it helps towards understanding the other Ruthroff balun configurations.
[Hits: 3 127 | Votes: 6 | Rate: 3.33] - The Guanella 1:4 balun
- A cost effective current-mode 1:4 balun can be constructed from two lengths of coax, two ferrite rods, some electrical tape, cable ties, a length of PVC water-pipe and some connectors. This form of 1:4 current-mode balun is named after G. Guanella.
[Hits: 2279 | Votes: 1 | Rate: 10.00] - Build a HB 4:1 voltage BALUN for 1KW
- In depth detail with photos on how to build your own HB 4:1 voltage BALUN that will run 1KW. Inexpensive and fun to build.
[Hits: 465 1 | Votes: 12 | Rate: 6.9 1] - A 4:1 Balun
updated
- A single-core 4:1 current balun of improved performance by Chris Trask N7ZWY PDF file
[Hits: 14386 | Votes: 6 | Rate: 4.83] - 4:1 balun for 160 to 10 meters
pop
- Articke By Clay Wynn
[Hits: 22 115 | Votes: 6 | Rate: 5.83] Antennas : Feed Lines : Choke
- Choke Balun Designs
- In this designs G8ODE explains different methods to builds a choke balun
[Hits: 159 1 | Votes: 3 | Rate: 3.33] Antennas : Theory
- SWL antenna distribution system
- A methodology for connecting multiple LF/MF/HF receivers to a single antenna via readily available and inexpensive 75-ohm TV cable. Custom made baluns and splitters provide impedance matching and prevent interaction between receivers.
[Hits: 1052 | Votes: 1 | Rate: 8.00] Antennas : Windom
- OH7SV Matti Hohtola Ham Projects
pop
- The most modern QRP transceiver in 2004,Direct Conversion HF Transceiver with DDS LO,
50 ohm to 200 ohm HF wide band transformers,
Wilkinson splitter for RX measurements,
Windom baluns 2001/2004,
Ferrite rod antenna for 80 meter, Magnetic Loop Antenna for 80 m, Mascot Switched PSU 9320 modification to 8A peak current, 150W MOSFET linear amplifier for 80m, 80 m HF SSB/CW Transceiver
[Hits: 16332 | Votes: 22 | Rate: 8.04] Technical Reference : Components : Toroids
|
|
