wi fi antenna

wi fi antenna

Pages: [prev] ... 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 [next]

• Budget-Friendly 5-Element Quad Antenna Design - Constructing a 5-element quad antenna, the author aimed for low cost and simplicity, resulting in an effective design with 11 dBi gain and SWR of 2:1 or better across the 2-meter band. Using wood and dowels, the antenna costs under $8 and takes less than two hours to build with basic tools. The model predicts excellent performance, confirmed by ARRL Lab measurements. Practical field results demonstrate improved communication, even in simplex mode.
  [ Hits: 118 | Votes: 1 | Rating: 7 ]

• Online LInked Dipole Designer - The page for designing linked dipole antennas allows users to swiftly create a versatile multi-band antenna suitable for portable applications in outdoor settings, such as in the field or on mountain tops.
  [ Hits: 99 | Votes: 0 | Rating: 0 ]

• Field-Tested VP2E Antenna - The author explores the VP2E antenna, introduced by Ed Durrant DD5LP, for Portable Operations on the Air (POTA). Detailing its unique design, successful trials, and an unexpected propagation twist, the VP2E proves a promising addition to the author's portable antenna arsenal.
  [ Hits: 521 | Votes: 5 | Rating: 4.8 ]

• TEFV Terminated End Fed Vee Antenna - The Terminated End Fed Vee Antenna (TEFV) is a travelling wave antenna with constant current distribution. Unlike traditional resonant antennas, TEFV operates without standing waves, using a terminating resistor for broadband efficiency. With a combination of vertical and horizontal polarization, it offers wide bandwidth from 1.8 MHz to 30 MHz, eliminating the need for a tuner. Key components include a 9:1 unun transformer and a 500-ohm terminating resistor. Grounding and counterpoise enhance performance, and it can handle power losses of up to 30%. TEFV provides an effective, versatile antenna solution for amateur radio and broadcast applications.
  [ Hits: 187 | Votes: 2 | Rating: 6.5 ]
• G4WIF End Fed Half Wave Antenna  ^updated - Opting for a visually appealing inverted L configuration, G4WIF anchors the End Fed Half Wave antenna to an old clothes line pole, seeking cost-effectiveness in their endeavor. Despite initial misconceptions about transformer components, a £7.95 investment in a T240-43 toroid and DIY mounting container resolves the issue. Reflecting on commercial alternatives, G4WIF's homemade solution proves both economical and sufficient for their amateur radio needs.
  [ Hits: 119 | Votes: 1 | Rating: 9 ]

• EFHW Anntenna 40-10 for QRP - The author discusses their endeavour to create a compact, robust resonant antenna for QRP operations due to strong winds in their area. Primarily designed for 40m and 20m bands, the article offers adaptability for different bands. The author hints at future projects, including an extended 8010 EFHW variant, promising a lighter yet efficient design.
  [ Hits: 53 | Votes: 0 | Rating: 0 ]
• Comparing Mobile whip versus EF HW Vertical - PH0NO conducted field tests comparing a mobile antenna (DX-UHV) to an end-fed half-wave wire. Results on 20m showed the end-fed wire outperforming the mobile antenna, with a significant difference in signal strength. On 40m, the end-fed wire surpassed the mobile antenna in spots and reach. While the mobile antenna is more practical, the end-fed wire offers superior performance. Further testing is planned.
  [ Hits: 81 | Votes: 0 | Rating: 0 ]

• RF Choke with Bifilar Windings - This article presents an RF Choke featuring an 11-bifilar turn winding of #14 house wire on a Fair-rite FT240-31 toroid. The choke is enclosed in a 3D-printed case from Thingiverse, though this may pose thermal concerns at higher power levels. With SWR concerns up to 30MHz, the author plans to employ two series chokes at the rig input for improved performance. This choke offers versatility for portable use, with potential mismatch resolution using an antenna tuner. Further testing is anticipated upon the arrival of new cables.
  [ Hits: 86 | Votes: 0 | Rating: 0 ]

• Choosing the Right Aluminum Stock for Antenna Building - Building an efficient antenna begins with selecting the right aluminum stock. This article provides a comprehensive guide to sourcing aluminum materials for antenna construction. It covers different aluminum grades, their tensile strengths, tempering options, and their suitability for various antenna components. The article also recommends reputable suppliers in the UK, making it a valuable resource for antenna builders seeking durable and high-performance materials.
  [ Hits: 76 | Votes: 0 | Rating: 0 ]
• Antenna Manufacturing: How to Prevent Galvanic Corrosion - Galvanic corrosion, a destructive process triggered by dissimilar metal contact in a corrosive electrolyte, poses a significant threat in antenna manufacturing. With aluminum and stainless steel components commonly involved, unaddressed corrosion can lead to white particle accumulation, causing long-term damage. Awareness of the galvanic series and the application of protective coatings like Alumslip can mitigate this pervasive issue, ensuring a prolonged antenna lifespan.
  [ Hits: 55 | Votes: 0 | Rating: 0 ]

• Enhancing Performance with W8JK/MOXON Antenna Variant - F5NPV introduces a variant of the W8JK antenna design, employing the MOXON principle. With extended monopoles, it outperforms the Open-Folded W8JK, yielding a 1dbd gain improvement, enhanced performance on 30m and 10m bands, bi-directionality, and lower side attenuation. The design's focus on higher radiation impedance results in increased antenna efficiency and reduced losses. Despite these improvements, the bill of materials remains unchanged.
  [ Hits: 182 | Votes: 0 | Rating: 0 ]

• Space-Efficient Excellence: Inverted L Multi-Band HF Antenna - Discovering a solution for limited space, the inverted L HF antenna emerges as a stellar performer. Half the size of a dipole, it ensures optimal installation in restricted areas, maintaining superb transmission (TX) and reception (RX) characteristics. Spectrum Communications' multi-band version, featuring traps, proves even more space-friendly without compromising performance. A fiberglass pole offers sturdy support, while proper grounding, an RF choke, and occasional tuning contribute to a high-performing and reliable antenna system.
  [ Hits: 186 | Votes: 0 | Rating: 0 ]

• A Compact and Stealthy Field Portable Antenna - In the quest for an ideal field portable antenna, the author recounts experiments involving various wire configurations. While a previous candidate, a 41ft random wire, proved effective but lacked stealth, the search led to a surprising rediscovery of a design previously rejected—the Rybakov Antenna. With a focus on simplicity, rapid deployment, and multiband capability, the author explores the versatility of a 26ft Rybakov, avoiding the halfwave trap. The article delves into the antenna's performance and its potential as a discreet, resonant solution for field operations, addressing the challenges encountered during a POTA activation. Additionally, the Unun/Balun design used in conjunction with the Rybakov Antenna is discussed, providing insights into achieving a balanced system.
  [ Hits: 153 | Votes: 1 | Rating: 1 ]
• Portable Half-Square Antenna: - The author explores a portable version of the half-square antenna, typically a single-band structure. Using a 9:1 unun for versatility, they describe construction with speaker wire, deployment using collapsible poles, and field tests, achieving successful contacts on multiple bands. The article suggests efficient matching methods and concludes with the antenna's integration into the author's portable options.
  [ Hits: 126 | Votes: 0 | Rating: 0 ]
• Yaesu ATAS-120A Portable Tripod: Enhancing Efficiency - In this post by N6CTA, discover the conversion of the Yaesu ATAS-120A screwdriver antenna for portable use. The author details the creation of two sets of radials, 16 and 32 in 16ft lengths, aiming to optimize the efficiency of ground-mounted antennas. Additionally, insights are shared on attaching male quick disconnect blade tabs, with potential plans for a radial plate kit.
  [ Hits: 87 | Votes: 0 | Rating: 0 ]

• Build a W3DZZ Antenna - The purpose of this construction is to enable the realization of an HF antenna called W3DZZ with minimal equipment and low cost. It allows traffic on the bands 3.5 / 7/14/21 and 28MHz.
  [ Hits: 219 | Votes: 1 | Rating: 1 ]

• Ham Radio And the Art of Bushcraft - This article explores the marriage of amateur radio and bushcraft, advocating the pleasure of setting up a portable station in nature rather than operating from the confines of a vehicle. The Parks on the Air (POTA) programme is highlighted as a catalyst for outdoor radio activities. The author shares his experiences and techniques, from transporting equipment into the wilderness to setting up shelters and antennas. Knot tying skills and the use of frogs are emphasized for efficiency, and a unique method for launching wire antennas is described. The article emphasizes the synergy between amateur radio and bushcraft skills, enhancing the enjoyment of radio operations in wilderness environments.
  [ Hits: 83 | Votes: 1 | Rating: 10 ]

• Greencube (IO-117) Guide to Setup, Software and Operation - Explore the detailed setup, essential software, and operational nuances for Greencube (IO-117), a Medium Earth Orbit (MEO) satellite with a 70cm digipeater, offering DX possibilities for amateur radio enthusiasts. From antenna configurations to software choices, this guide covers everything for a successful Greencube experience.
  [ Hits: 141 | Votes: 0 | Rating: 0 ]

• DIY Tree Antenna Launching: Cheap and Effective - This article explores budget-friendly methods for launching wire antennas into trees, comparing common options like slingshots and professional arborist tools. The author introduces a simple and cost-effective DIY approach using latex balloons, sand, and readily available materials for efficient antenna deployment in the field
  [ Hits: 119 | Votes: 0 | Rating: 0 ]

• Smart SO2R Antenna Switcher: A DIY Solution - In pursuit of enhanced station efficiency, the author describes crafting an Arduino-based smart antenna switcher for an SO2R setup. Faced with manual antenna switching challenges during contests, the project utilizes a Logos Electromechanical 4x4 Driver Shield and a Power Screw shield for seamless functionality. Despite its raw appearance, the automatic switcher proves indispensable in contest scenarios, prompting considerations for future improvements and standardization of station control protocols.
  [ Hits: 152 | Votes: 0 | Rating: 0 ]

Pages: [prev] ... 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 [next]