Search results

This Field Day Vertical Antenna project is the result of many years of attending various field day sites and realizing that what was needed is a simple, easy to assemble vertical antenna.

The terminated tilted, folded dipole T2FD is a little known antenna that performs excellently. Compact in size compared to a half-wave dipole the T2FD provides signal gain, wide frequency coverage, and exceptionally low noise characteristics.

These devices are called Traps, but they are actually more like frequency sensitive switches. They are parallel resonant, high Q, tuned circuits which provide a very high impedance at their frequency of resonance.

Calculate your dipole, 3 element yagi and a simple dipole

The IK-STIC 2 is a vertical, all band, antenna that is over 25 feet tall yet weighs under 5 pounds. Based on a telescopic pipe or a fiberglass fishing pole, using a tuner it can easily cover the amateur radio HF bands from 40 - 10 Meters

What type of antenna should I get? Well, the best type of antenna for working the OSCAR satellites are circular polarized antennas

The K4VX linear-loaded dipole for 7 MHz, simple and practical way to make a short but efficient 40-meter dipole.

Why a vertical antenna or longwire antenna might require a balun

VE7CA reprint an interesting article taken from arrl antenna compendium. Two elegant practical and portable 6-meter gain antennas, a two-element quad and a tree-element Yagi antenna for 50 Mhz-6 meter band

KO4NR coax cable antenna switch construction by ve3cgc

the multiband Notebook Antenna, so called because the entire antenna will fit easily inside a 1" thick 3-ring binder

Welcome to the web site of Wilson Antenna, Inc., manufacturers of the worlds most powerful CB antennas for the automobile and 18 wheel tractor rigs.

A 40m through 17m Mini End Fed Half Wave Antenna Coupler by Steve Yates - AA5TB

design by Brian Williams, GW0GHF

Phased array Ground Planes antennas for 144 Mhz

Wire antennas requires a special coupling network to properly couple my 50 ohm coax to the antenna's high impedance (5000 ohms)

This end fed type of antenna was marketted in the UK and is a useful system for the portable set-up. Being a half wave, no radials or counterpose wires are needed.

20 meters through 6 meters, antennas

Homebrew balanced-L antenna tuner. Covers 160-10m. Designed specifically for balanced feedlines.

An HB9CV antenna for the 70 cm band in french

The original G5RV antenna system consists of a center-fed horizontal 102' wire plus a 34' length of open-wire 525-Ohm feeder. Louis Varney, the antenna system's developer, intended two other features. Learn more at Cebik website

Input the desired resonant frequency and it will calculate lenght in inches feet and meters

Antennas that use a combination of vertical and horizontal polarisation.

If you want an antenna resonoant on the 160 meters band this is a possible solution, but of course, need space.

Dimension and formula for a 4 element QUAD antenna for the 10 meters band

This antenna article is geared towards new Hams and antenna builders looking for a very inexpensive 6 band antenna that can be efficiently fed with 50 ohm coax without a tuner by N4JTE

JA7KPI windom antenna page

This is my simple implementation of the ARRL Antenna Book design equations for the axial-mode helical antenna.

Pictures of the 160 meters dipole antenna at W5JGV

G0KYA slim jim antenna for 10 meters band

A design of a 2 m quagi antenna by TA2IB

W5ALT Indoor Vertical Antenna is a base loaded vertical antenna that can be tuned on almost all HF bands by adjusting a big coil. Operating a ham radio station from an apartment in Maracaibo, Venezuela, the author demonstrates effective communication with over 100 countries using a custom-built indoor vertical antenna. Addressing common misconceptions, the design uses a balanced approach with radials and a base-loaded vertical element made from affordable materials. The antenna fits discreetly indoors, covers 6 to 40 meter bands, and achieves acceptable SWR with an MFJ tuner. Despite limited space and typical apartment challenges, the setup enables reliable DX contacts, confirmed by numerous QSL cards, proving indoor antennas can perform well in constrained environments.

Inverted V antennas is a dipole with the center raised on a mast and the endpoints near ground. Calculate dimensions online.

8 and 4 elemets yagi beam antenna by N6CA

The Joystick antenna was used many years ago as an all band vertical HF antenna under restricted space situations that would cover from 80 meters thru 10 meters with a tuner and was a great commercial success Some hams even had success with it on 160 meters.

This antenna project came out very nice. It's a rugged homebrew multi-band trap vertical antenna that works the 10, 15, and 20 meter amateur radio bands. The antenna can be mounted on the ground or on a mast. Mounted on the ground the antenna has a low take off angle for working DX. If mounted on a mast the antenna will acheive both a low angle as well as another radiation lobe that has a much higher take off angle.

Adding an external antenna to the Belkin F5D7050

A Parasitic Lindenblad Antenna for 70cm by Anthony Monteiro, AA2TX. This is the official 16 pages PDF File published by AMSAT about the 70cm Parasitic Lindenblad Antenna.

A Portable Low Frequency Antenna Analyzer, For those of us who like to play with antennas on the ham bands, one of the handiest tools to have around the shack is an "antenna analyzer". These gadgets combine a signal generator and standing-wave ratio (SWR) sensor in a small battery-powered unit.

A 40-meter reversible _Moxon rectangle_ antenna project details its construction and performance, featuring 51-foot long sides and 7.7-foot turned-in sections. The design incorporates a 16.5-foot boom, with elements spaced 1.1 feet apart, constructed from #14 covered wire. It utilizes two double-pole relays for switching between NE and SW directions, achieving F/B ratios up to 40 dB on CW and 30 dB on SSB, with distinct reflector stub settings for each mode. This antenna replaced a full-size 2-element Yagi, demonstrating comparable forward gain while offering superior F/B ratios and directional flexibility. _EZNEC_ modeling indicates only 0.2 dB less forward gain than the Yagi. The system uses no baluns, relying on half-wave feedlines and switched stubs for impedance matching. The antenna is tree-supported at 45 feet, with its effective radiation height modeled at 80 feet due to local terrain, enhancing its performance over a nearby lake.

Online calculator for Cantenna special antenna for 802.11 Wi-Fi bands

An attic indoor antenna successfully implemented by N9RET by using two runs of 2-conductor wire

Active antenna with a frequency response that is flat from 5kHz to over 30MHz

This very large moxon antenna resonate on 80 40 and 10 meters, has been used for CQWW 2006 by a YU team project

A shortened multiband antenna, about 23m long, for 80m - 10m bands with a low SWR (<1.3) on 80m and 40m, and < 3 till 10m. Bandwith on 80m is 300kHz

Tennamast design and manufacture a wide range of fabricated metal goods, Antenna masts, Wind-sock masts, and masts for holding such systems as CCTV, Loudspeakers, Lighting units

Java script antenna calculators for ground planes, half wave verticals, quad antenna, 5/8th wave vertical antenna, dipole and inverted vee antennas

K4TR Manufacture and sell simple dipoles, half square 2 wire phased vertical arrays, end fed zepp antennas, G5RV antennas. 1:1 baluns

VHF Antenna in a lunchbox. The magnetic loop on two metres band Lloyd Butler VK5BR

Here's an antenna that you can take with you. This is made from cheap flat 300 ohm TV antenna wire.