Radio Frequency Interference
Reducing radio frequency interference
Sort:
Subcategories
- BPL (16)
- Noise Reduction (32)
- PLT (2)
Related Categories
-
SDR as an RFI site survey tool. This article will show how a site survey tool was built to use in RFI mitigation. -
Are you suffering from TVI? Then why not try this filter for size. It is a three-stage high-pass filter that blocks low-frequency 50MHz signals while letting through UHF TV. -
Understanding and solving RF interference problems using ferrite -
University of Texas Amateur Radio Club RF-Calculator. This is a main beam power density estimation program intended for use as part of a routine evaluation of RF safety compliance with FCC regulations -
How track and solve electrical interference from you computer -
Installing mobile radios in your new megabucks car can be a frightening proposition - especially if RF from your rig could damage your shiny new roadster -
The intrepid newcomer encounters common mode problems in a mobile environment. Implementing some common mode chokes will be possible to reduce interferences -
Excellent article on limiting noise using chockes by Chuck Counselman, W1HIS -
The goal of detuning is not to avoid resonance, but rather to minimize re-radiation and/or current in the interfering structure. -
RADIOING eEngineer RFI EMI information -
The circuit described below will substantially reduce or completely eliminate interference from almost any local source whilst leaving the wanted signal relatively unaffected, even though it may be on the same frequencey by TREVOR, G3ZYY -
Does your Amateur Radio system comply to the EMI rules ? (German values implemented) -
Radio Frequency Interference To/From touch lamps and dimmers -
Information about RF driven lamps -
Connecting centre fed antennas, dipoles, yagis, rhombics, loops to coaxial cable, unless care is taken, it is not difficult to end up with feeder radiation resulting in power loss and the radiation characteristics changes -
Using ferrite to reduce radio frequency interference with your PC monitor or antennas with your receivers or transceivers. -
This article is about the characteristics and use of various filters and ferrites for solving amateur radio electromagnetic compatibility problems involving breakthrough of amateur signals into domestic equipment such as television sets, video recorders stereo sytems etc. -
RFI/EMI RadioFrequency interference/electromagnetic interference by ARRL Technical Information Service page -
Ham radio transmissions can interfere with television reception. This is called television interference, or ham radio TVI. Consumer adoption of cable television has significantly reduced ham radio TVI. But the introduction of IPTV, or television over phone systems, has brought ham radio TVI back, often with a vengeance. Here's why -
RF Choke to prevent hf currents on the feedline. This Magnetic Longwire Balun (MLB) makes it possible to efficiently use a coaxial lead-in cable with all forms of longwires, T-forms or other types of wire antennas, without the need for an antenna tuner. -
A very beginner's guide to coax cables. Characteristics, detailed comparison of typical coaxial cables, commonly used connectors, and a few words about SWR. -
An old post by John Doty about effects of noise in longwire antenna. -
This site is dedicated to mobile amateur radio operators, old and new alike. Whether you are into HF, or VHF operation, I trust the information presented will increase your enjoyment of our great hobby. With safety as a byword, there are articles on amplifiers, antennas, bonding, impedance matching, installing hardware, mobile equipment, noise and RFI abatement, wiring, and much more. I do my best to keep these articles up to date, and easy to follow. -
Why a vertical antenna or longwire antenna might require a balun -
Getting squeaks and squawks from your H-T? Are pagers crunching your mobile rig's front end? Here's how intermod happens--and how to fight back! -
RFI mailing list at contesting.com -
Dealing with Computer generated RFI/EMI by Daniel 9V1ZV -
With all the wire you have out, you may run into a problem with static buildup on the antennas. This static may try to make its way into your receiver, causing you major problems and damage that can run into a lot of money. -
If you are having problems with RFI from Solar Panels this document from QST provides useful advice. According to this article it is possible to prevent and mitigate RF interferences, with your amateur radio equipment, by suppressing the RF either in the shack and to the solar power infrastructure. -
Telephone EMI, questions and answers on how to solve interference problems to phone lines -
The video delves into the significance of interference reduction in ham radio setups by utilizing ferrite materials. It demonstrates the use of spectrum analyzers and tracking generators to showcase the performance of ferrite devices in minimizing noise levels. The analysis includes insights on resistance levels, attenuation factors, and the impact of using multiple ferrite clamps or rings to enhance noise reduction capabilities. Viewers gain a deeper understanding of ferrite composition, characteristic curves, and winding techniques for effective noise attenuation in different frequency ranges. Overall, the video serves as a comprehensive guide to optimizing interference reduction in radio environments through the strategic use of ferrite materials. -
This little gadget is that it allows you to tune up at full peak output power, whilst limiting the average power to a fraction of the peak, thereby protecting the PA from meltdown -
Nearly half of all reception problems are due to deficiencies or faults in the television receiver, the aerial lead or the aerial. This article will help you to check whether the problem you are having is due to one of these causes. -
TVI and BCI bandpass and bandstop filters in SMD technique. Schematics and images. -
High pass filter schematics for TVI and examples of finished filters -
An Energy Analysis at an Impedance Discontinuity in an RF Transmission Line -
Removing disturbing RFI from the Behringer HA400 Headphone Amplifier, using ferrites and capacitors soldered in the main circuit board of the small amplifier. -
The main function of the Ugly Balun is to help eliminate rf currents from flowing on the outside of coaxial cable using the principle of choke action. -
In this article the author describes some new designs of ferrite loaded chokes for suppressing unwanted common mode currents at HF applied to feed lines like choke baluns, but also in the shack, applied to various coaxial, mains and data cables -
An article by microHam about guidelined to eliminate problems caused by RFI -
Eliminating RFI/EMI Interference from your Audio System -
Troubleshooting your power supply, in determinig connections to battery, alternator and regulator interference and checking power supply leads. -
A amateur radio guide to RFI, ferrites, baluns, and audio interfacing by K9YC -
Can Home Solar Power and Ham Radio Coexist? It is possible, with minimal interference from the solar power system, provided you make some modifications. -
Learn about the design and construction of a hybrid low-pass filter for HF transmitters, specifically tailored for operation in the 6 meter band. The filter utilizes a single elliptic link for high cutoff steepness and deep VHF/UHF suppression, requiring only two standard capacitor values. The article discusses the necessity for improved filtering due to changing technological landscapes and the increasing sensitivity of VHF/UHF radio channels to interference from various sources. Detailed circuit schematics and performance characteristics are provided, ensuring minimal degradation of antenna system VSWR when integrating the filter into the setup. -
How to solve RFI problems caused by the charge controller, which is a PWM type charge controller, that generates a lot of EMI interference -
I have RFI, now what– Locating it. This article is the first of a three parts article, that covers the problem of locating the RFI source. Author make use of an SDR receiver to locate RFI emissions. Ai interesting RFI location process diagrams helps on following the various phases, permitting the discovery of almost 75% of the RFI issues. -
This article addresses the issue of unwanted RF in amateur radio setups and introduces a practical method to measure common-mode currents (CMC) using a homebuilt RF meter. The meter, constructed with readily available materials, measures unwanted RF on the coaxial cable shield by inductively coupling to the shield using a split-bead ferrite. The article provides detailed instructions on building the meter, interpreting measurements, and using ferrite chokes to mitigate RF interference. Emphasis is placed on the importance of verifying CMC levels and installing chokes to improve equipment performance. -
This article will cover gathering some software tools used for RFI location and removal. -
Effects and intereferences caused by LED lights in the shack -
A proven and practical approach to dealing with RFI from grow lights and more. -
In this study, the author builds upon Muncy's research, demonstrating that radio-frequency current on cable shields affects audio systems through the "pin 1 problem" and shield-current-induced noise (SCIN). An enhanced equivalent circuit for ferrite chokes is proposed, addressing dimensional resonance and inductor self-resonance. Field tests confirm that chokes reduce interference across 500 kHz to 1,000 MHz. Guidelines for diagnosing and mitigating EMI from various sources are provided for product development and field installations. -
QRM.guru has been developed to assist radio hams in dealing with RF noise. This is an educational and reference resource. -
The article details how to eliminate Radio Frequency Interference (RFI) from the Behringer HA400 headphone amplifier when used in ham radio setups. While the HA400 is praised for its quality and affordability, it was not designed for RF environments, causing distortion when used with a 500-watt radio station. Initial attempts using clamp-on ferrites on the headphone and power cables only partially resolved the issue. Upon opening the unit, the author discovered the circuit lacked RF bypassing components. The solution involved installing 0.1μF (104) capacitors at key points in the circuit: the power supply input, audio circuits, and op amp inputs. This modification, combined with the external ferrites, completely eliminated the RFI problem, making the unit suitable for ham radio operations. -
Learn how to eliminate RF interference from your Behringer HA400 headphone amplifier for a better listening experience. Discover the simple modifications needed to prevent distortion caused by RF in your audio setup. Follow the step-by-step instructions provided by WB5NHL Ham Radio to improve the performance of your headphone amplifier in ham radio activities. -
Ham Station Desk Radio Equipment Ground -
This article discusses the potential for solar power systems to coexist harmoniously with amateur radio, challenging the notion that they are inherently incompatible. Drawing from personal experience, the author emphasizes the importance of selecting RF-quiet components, focusing on series-string Sunny Boy grid-tie inverters. The article also highlights considerations for system design and limitations based on roof orientation, shading, and array size. Overall, it presents a valuable perspective on creating a radio-friendly solar PV setup. -
A workaround to common RF interference on Samsung TV LED causing several issues like changing channel, swithcing to demo mode, or changing volume. -
Stop EMI RFI Interference in Off Grid Solar PV Systems, in this article the author provides hints on tracking down the EMI or RFI source, shielding and grounding in order to eliminate interferences on the whole HF and VHF ham radio bands -
This fall/winter 2 events has happened at about the same exact time. I finally got around to putting up an end fed long wire for 80M (and maybe 160M) The fridge big the bullet and we ended up purchasing a new fridge. -
Article on radio frequency interferences, with a long list of common RFI cause, like Plasma TV, Solar panels inverters, fluorescent tube lamps. -
There are several reasons that can cause coax line radiation, most of them are related to wrong or missing use of a balun, but none can be imputed to load mismatch. -
Articles on the correct placement of ferrite noise suppressors are common, but little has been written about the different options and where to buy them. This page contains an interesting comparison of several ferrite types used to reduce RFI. -
A simple TVI Filter schematic -
Radio Frequency Interference (RFI) has always been a source of concern for the Radio Amateur. Until the recent introduction of complex circuitry in the home, our communications gear has been the main source of potential RFI. In this computerized age of ours, increasingly complex and sensitive receivers are being barraged by these and other sources of RFI. -
This article explains how software-defined radios (SDRs) are used to detect and visualize radio frequency interference (RFI). In part one, Dave details the process of capturing and analyzing RFI on the 80-meter band over a 24-hour period using tools like S-Meter Lite and Spectrum Lab. The SDR's wideband capabilities help identify and document RFI sources across large frequency ranges, making it a valuable tool for RFI detection and mitigation.
